Transportation

Results: 528

2-Person Companion Car

The 2-Person Companion Car is an adapted golf cart or personal electric vehicle designed for use by individuals with walking, circulatory, or balance disabilities, arthritis or limited stamina. This golf cart enables a person seated in the rear seat to play golf without getting out of the car and without having to operate or steer the cart. A companion in the front seat operates the vehicle. When the cart approaches a golf ball, the passenger in the back seat can rotate the seat and hit the ball

6-Way Power Seat Base

The 6-Way Power Seat Base is a vehicle driver powered seat base for people with lower extremity and mobility disabilities and spinal cord injury. The seat base eases transfers to and from a wheelchair. It has a front-to-rear travel of 13.5 inches, a height adjustment of 9 inches, and a 90 degree power swivel. All functions are independent to create numerous adjustments. The seat base is adaptable to most factory or retrofit vehicle seats. POWER: Vertical power is operated by 12 Volt DC, 16 Amp c

7000 Series D.C. Metro Bus

The D.C. Metro Bus 7000 Series is an American with Disabilities Act compliant metro bus that is designed for all people, for those in wheelchairs and those with mobility disabilities to ride to and from places with comfort and stability. It's ergonomic design allows for 2 more inches in the aisles on both sides, has a separate section for those in wheelchairs. Replaced the 1000 and 4000 Series metro buses. Seats 40 more people. Speaker is in real time and automated so it's clearer to understand

Abiloader-Fo

The AbiLoader-FO is a wheelchair loader for car, pickup truck, sport utility vehicle and van designed for use by people with lower extremity or mobility disabilities, spinal cord injury and other who use wheelchairs. It is intended for use with folding wheelchairs. The device is installed in the trunk or rear storage area of a vehicle into which the folded wheelchair will fit. The AbiLoader-FO has a robotic arm with two actuators and a mechanism to grab and hold a wheelchair. There is a third ac

Abiloader-Fx

The AbiLoader-FX is a wheelchair loader for car, pickup truck, sport utility vehicle and van designed for use by people with lower extremity or mobility disabilities, spinal cord injury and other who use wheelchairs. It is intended for use with wheelchairs with fixed frames that do not fold. The device is installed in the trunk or rear storage area of a vehicle into which the folded wheelchair will fit. The AbiLoader-FX has a robotic arm with two actuators and a mechanism to grab and hold a whee

Accelerator / Brake Guard (Model 3571)

The Accelerator/Brake Guard, model 3571, is an accelerator and brake pedal guard designed to protect individuals with lower extremity disabilities who drive using hand controls against inadvertently pressing the accelerator or brake pedal. This device also prevents the user from placing his or her foot underneath either pedal. The unit features a release mechanism that allows the guard to be easily removed without tools, permitting ambulatory drivers full use of the accelerator pedal. It has a c

Accelerator / Brake Guard Lowered Floor (Model 3572)

The Accelerator / Brake Guard Lowered Floor, model 3572, is an accelerator and brake pedal guard designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and others who use wheelchairs and use hand controls when driving and automobiles. Designed for use in lowered floor minivans, this unit prevents the user from inadvertently pressing the accelerator or brake pedal or placing a foot underneath either pedal. The unit has a release mechanism that allows t

Accelerator Guard (Model 3570)

The Accelerator Guard, model 3570, is an accelerator pedal guard designed to protect against inadvertently hitting the accelerator pedal for individuals with lower extremity disabilities or spinal cord injury who use hand controls. The device attaches on the same base as the left foot accelerator pedal. The unit features a release mechanism that allows the guard to be easily removed without tools, permitting ambulatory drivers full use of the accelerator pedal.

Accelerator Shield (Model 103)

The Accelerator Shield, model 103, is an accelerator pedal guard designed to protect against inadvertently hitting the accelerator pedal when using hand controls or during leg spasms. The device attaches below the accelerator pedal with an angular rod extending over the pedal at an angle.

Ace-Aut Secondary Controller

The ACE-AUT Secondary Control Center is a computer-controlled driving system that operates all secondary accessory driving functions. The control center is programmed to operate 48 driving accessory functions. It is operated by a small, six-button console. Visual displays by the original equipment manufacturer are unobstructed by this compact configuration. The dash-mounted display visually cues each function. Standard euqipment includes manual override switching and self-cancelling turn signals

Ada Prisoner Transport Chevy Van

The ADA Prisoner Transport Chevy Van is a custom built van conversion designed for use to transport prisoners seated in wheelchairs. This vehicle is built to optimize space, safety, and security for both the transporters and the prisoners. It includes video and networking capabilities that allow the transporters to monitor the status of the prisoners without stopping the vehicle and compromising their own safety. All compartments are equipped with advanced mobile digital video recorders (DVR), w

Adapta Van

The Adapta Van is a van conversion designed for commercial business and organizations that provide transport for individuals who use wheelchairs. Conversions can be done for Chevy, GMC, and Ford vans. Features include an aerodynamic fiberglass top, raised cargo doors, solid core marine grade plywood with lap jointed seams covered with non-slip diamond patterned vinyl, and a four-point wheelchair securement system with recessed aluminum L-track. Conversions can accommodate a variety of interior t

Adapted Jeep

DO-IT-YOURSELF-ENTRY --- PURPOSE: To enable a person who uses a wheelchair to use a Jeep. A used passenger seat, small crane, and a winch were used to create a hoist that lifts the user into the passenger seat and the wheelchair into the rear cargo area. MATERIALS: Automotive passenger seat, small crane, and a winch. TOOLS: Shop tools. SKILLS REQUIRED: Basic shop and mechanic’s skills. TITLE: Doing It Yourself. JOURNAL: Quest. REF: Volume 12, Number 1, January/February 2005. WEB: http://www.mdau

Adapted Mercedes 190E

The Adapted Mercedes 190E is a voice activated, microcomputer based driving control system adapted for the Mercedes Benz 190E automobile. Steering, brakes and accelerator are foot controlled. Other functions are voice controlled; provides up to 50 commands. Voice activated functions include operation of the hand brake, headlights, automatic gear shift, turn indicators, radio, and windshield wipers.

Adjust-A-Pillow Car Neck Pillow

The Adjust-a-Pillow is designed for use by individuals with neck pain, injury, or disability. It keeps users neck in a comfortable position while you're driving, or can even be used around the house when you pick up your favorite book or lay down for a nap. It has six adjustable positions to ensure you have the most support and comfort you can possibly imagine. The material is soft on the skin and the zippered cover can be removed for cleaning. Lay the Adjust-a-Pillow Car Neck Pillow flat to u

Adjustable Angle Key Holder.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Device allows alternate hand positions to be used when holding a key to unlock a door. Photo shows one example of key lengthened by attaching simple hardware. Suggestion is to determine best hand position for functional key use, then adjust angle of key holder to correspond to the angle of the lock in the door. SKILLS REQUIRED: Assembly. AUTHOR: Gugerty, J.; Tindall, L. TITLE: Tools, Equipment & Machinery Adapted for the Vocational Education &

Aero Access

Aero Access is a public transport van designed for use by individuals with mobility disabilities or spinal cord injury. The van has a folding ramp at entry and space for up to eight wheelchairs. Other features include a Freightliner FB 65 chassis; Cummings ISB 5.9 liter diesel engine; Allison Model 2000 transmission; front wheel drive; Double Cardan steering joint; tilt hood/fender for easy engine access; independent, rear air suspension; welded steel uni-frame construction; 60 gallon fuel capac

Aerotech

The Aerotech is a public transport van designed for light to medium duty commercial bus use. The standard chassis is a E-350 Ford cutaway with a 4-speed automatic overdrive transmission. Other chassis features include power steering and brakes; tinted glass; air conditioning; and a 138, 158, or 176 inch wheelbase, depending on model. All models are able to provide handicapped accessibility and meet all applicable ADA requirements. A complete range of platform or passive-type wheelchair lifts, ti

Aevit L Series Gas And Brake Control

The AEVIT L Series Gas and Brake Control is a driving control system designed for use by individuals with lower extremity disabilities. This stand-alone accelerator and brake control system utilizes a lever input device with an adjustable maximum required input force ranging from 2.4 to 5.0 pounds. The input device can be positioned for either left hand or right hand operation, and the Gas/Brake input direction is user-selectable.

Aevit W-Series Steering System

The AEVIT W-Series Steering System is a small steering wheel designed for use by individuals with upper extremity disabilities. It utilizes a miniature wheel input device. The total number of rotations from full left steer to full right steer is 6-3/4 turns, which is approximately twice the rotations of the OEM steering wheel. The force input required to turn the wheel is 0.2 pounds as measured at a position of 3 3/8 inches from center. DIMENSIONS: Wheel input device is 6 inches in diameter.

Aevit Xj-Series Steering System

The AEVIT XJ-Series Steering System is a sensitized steering control system designed for use by individuals with upper extremity disabilities. This stand-alone steering control device utilizes a single axis joystick input device. The joystick is constrained to move only in the X-axis, that is, from side to side. The mechanism requires a maximum input force of only 0.2 pounds, and is internally spring-loaded to return to the center, or null, position. This input device can be positioned for eithe

Aevit Yj Series Gas And Brake Control

The AEVIT YJ Series Gas and Brake Control is a driving control system designed for use by individuals with lower extremity disabilities. This stand-alone accelerator and brake control utilizes a single axis joystick input device that requires a maximum input force of 0.2 pounds. The joystick input device is constrained to move only in the Y-axis and is internally spring-loaded to return to the center, or null, position. The input device can be positioned for either left hand or right hand operat

Aft Axle Fuel Tank For Ford E-Vans With Wheelchair Access (Model 080-01-10122)

The Aft Axle Fuel Tank for Ford E-Vans With Wheelchair Access, model 080-01-10122, is a fuel tank for van conversion designed for use by makers of vehicles for individuals with mobility disabilities or spinal cord injury. This system includes a 30-gallon aft of axle fuel tank to replace the original midship fuel tank in Ford E-Vans converted for wheelchair access. The system is designed for use in dropped floor conversions of 1997 through 2004 Ford E-250 and E-350 vans. This fuel tank is made fr

Aid For Removing Gas Cap.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Adapted knob turner can be used by those with limited hand function to remove automobile gas caps. Drill a hole in the center of a small piece of wooden rod or dowel that will serve as the handle. Epoxy a 1/4 by 6 inch rod into the handle. Weld a 1/2 inch U bolt to the other end of the rod. To use opener, hook the U bolt over the ears of the gas cap and twist. Another model, a wooden shaft with a handle is also described. SKILLS REQUIRED: Metalworking.

Air+Chair

The Air+Chair Onboard Transit Chair is a transfer wheelchair for onboard an airplane designed for use by individuals with lower extremity, mobility, and neurological disabilities, or spinal cord injury. This wheelchair is designed to fit narrow aisles and confined spaces for use in boarding aircraft. FRAME (HxLxW): 34 x 35.25 x 16.75 inches; when folded (HxDxW) 23.35 x 23.25 x 9.25 inches. It has a light gray solid welded frame with handles extending from the back. SEAT: Adjustable padded seat a

Aislemaster Boarding Transfer Chair (Models 8000 & 8010)

The AisleMaster Boarding Transfer Chair, models 8000 and 8010, is a transfer wheelchair for onboard an airplane designed for use by individuals with lower extremity, mobility, and neurological disabilities, or spinal cord injury. This wheelchair is designed to fit narrow aisles and confined spaces for use in boarding aircraft. Model 8000 fits jet aircraft and model 8010 fits commuter aircraft. FRAME (HxLxW): Model 8000 is 48 x 32 x 16 inches and model 8010 is 48 x 32 x 13 inches. Both models hav

Aislemaster Folding (Model 8020)

The AisleMaster Folding, model 8020, is an emergency evacuation carrier and transfer wheelchair for onboard an airplane designed for use by individuals with lower extremity, mobility, or neurological disabilities, or spinal cord injury. This wheelchair has a slender width and front-and-rear telescoping lifting handles to allow passage through narrow doorways, confined aisles, and stairways. FRAME (HxLxW): 47 x 32 x 16 inches; when folded (HxDxW) 147 x 17 x 16 inches. The frame is yellow. SEAT:

All Terrain Conversions

All-Terrain Conversions (ATC) specializes in converting trucks and SUVs into wheelchair accessible vehicles using their patented lift system. Their vehicles offer a solution for those with spinal cord injuries or other illnesses that limit their mobility.

Alumilite Folding Curb Ramp

The Alumilite Folding Curb Ramp is a portable ramp designed to provide access over curbs or steps or in and out of vans for wheelchair users. The ramp folds in half for carrying and comes with a handle and closing strap. The ramp is made of welded aluminum with a permanent non-skid surface that is integral to the aluminum and cannot tear or wear off. DIMENSIONS (LxW): 3, 4, 5, or 6 feet x 29 or 36 inches (open) and 15 or 18 inches (closed). WEIGHT: 18 to 41 pounds depending on size. CAPACITY: 60

Ameriglide 300 Vehicle Wheelchair Lift

The AmeriGlide 300 Vehicle Wheelchair Lift is a scooter or wheelchair loader designed for use by individuals with mobility disabilities. This lift fits into most vehicles and works with most scooters and electric wheelchairs, including Jazzy power chairs and Pride scooters. The lift arm rotates manually after the unit is pushed or pulled into or out of the vehicle. The unit has telescoping base legs, an adjustable-length extending boom with a boom arm end cap to protect vehicle headliners, and a

Ameriglide Auto Scooter Lift 350

The AmeriGlide Auto Scooter Lift 350 is a hitch-mounted scooter carrier designed for use by individuals with mobility disabilities. The self-adjusting hold down arm is compatible with most scooters on the market. As the large aluminum platform starts to lift after the user drives the scooter onto it, the hold down arm engages automatically and applies the right amount of tension to hold the scooter securely in place. The platform also folds up automatically when not in use. The lift can carry sc

Ameriglide Extender Plus

The AmeriGlide Extender Plus is a scooter or wheelchair loader for van designed for use by individuals with mobility disabilities. This interior-mounted lift can load a power chair or scooter into a full size van or minivan for transport. The lift is constructed from steel with a protective finish. It has an industrial rated 12-volt motor. The user drives on and connects the strap, and the lift loads the scooter or wheelchair. The maximum travel distance from the ground 26 inches. POWER: Uses ba

Ameriglide In-N-Out Mini Universal Lift 200

The Ameriglide In-N-Out Mini Universal Lift 200 is a hitch mounted or in-the-vehicle carrier for smaller power chairs or scooters. With this lift, the user can store a power chair or scooter inside a vehicle for transportation. This weather-resistant lift also installs on Class II or Class III hitches. OPTIONS: Wireless remote; docking device for Shoprider, Pride, or other scooter brands; receiver hitch. CAPACITY: 200 pounds. WEIGHT: 35 pounds. WARRANTY: Transferable limited 3 year warranty.

Ameriglide Manual Wheelchair Lift 100

The Ameriglide Manual Wheelchair Lift 100 is a hitch-mounted wheelchair lift designed for use by individuals with mobility disabilities or spinal cord injury. The user places a folded manual wheelchair onto the platform, then pushes a button to raise the wheelchair. The lift can be installed on almost any vehicle with a class I, II, or III hitch as well as standard ball mounts. OPTIONS: Swing-away arm; manual wheelchair cover; receiver hitch. POWER: Uses vehicle battery. DIMENSIONS (HxW): 5 to 1

Ameriglide Mini Power Chair Lift 135

The Ameriglide Mini Power Chair Lift 135 is a hitch mounted wheelchair loader designed for use by individuals with mobiity disabilities or spinal cord injury. It can be mounted onto a Class I, II or III trailer hitch from 5 to 19 inches high and used to transport most portable electric wheelchairs. A strap system secures the wheelchair to the lift. The lift is battery powered with a manual folding platform. Using the manual backup crank, the lift can be operated if the battery looses its charge.

Ameriglide Mini Scooter Lift 135

The Mini Scooter Lift 135 is a hitch mounted scooter loader designed for use by individuals with lower extremity, mobility, or walking disabilities. This powered lift can attach to a Class I, II, or III hitch from 5 to 19 inches high, and supports most 3- and 4-wheel micro-scooters. It has a manual fold down platform and a manual override, so it can be operated in the event of a power disruption. The scooter is held in place with a strap. POWER: Uses battery. An optional battery pack is availabl

Ameriglide Mini Universal Lift 200

The Mini Universal Lift 200 is a trunk mounted scooter or wheelchair loader designed for use by individuals with mobility disabilities. This inside lift can be used for transporting micro or travel size power chairs or scooters. It can be installed in the vehicle's trunk or cargo area. It rotates manually and can be disassembled for storage when not in use. POWER: An optional battery pack is available. OPTIONS: Wireless remote and docking device (Shoprider, Pride, or others). DIMENSIONS: 37 inc

Ameriglide Rear-Door Drive-Thru Lift 350

The Rear Door Drive-Thru Lift 350 is a powered wheelchair or scooter loader for vans designed for use by individuals with mobility disabilities. This lift attaches to the vehicle's third-row seating hardware. When in operation, a platform extends out on rails from inside until it clears the rear of the vehicle. From there, the platform lowers to the ground. The user drives the power chair or scooter onto the platform, attaches the straps, and presses a button on a remote hand control. The power

Ameriglide Side Door Drive-Thru Lift 275

The Side Door Drive-Thru Lift 275 is a wheelchair or scooter platform lift designed for use by individuals with mobility disabilities. The lift installs on second row seating harware, so the power chair or scooter can be delivered near the passenger or driver's door making it more convenient to move from mobility device to vehicle and back. When the lift is in operation, a platform extends out on rails from inside the vehicle until it clears the side. From there, the platform lowers to the groun

Ameriglide Tilt-N-Go 350 Mini Lift

The Ameriglide Tilt-N-Go 350 Mini Lift is a hitch-mounted scooter carrier designed for transporting travel-size scooters. This all- aluminum carrier uses a 2-inch Class 3 hitch. OPTIONS: Class 2 hitch adapter; mobility cover; Class 3 Receiver Hitch. DIMENSIONS (LxW): Usable platform area is 44 x 24 inches. CAPACITY: 350 pounds. WEIGHT: 46 pounds.

Ameriglide Universal 250 Lift

The AmeriGlide Universal 250 is a automobile or sport utility vehicle (SUV) lift for smaller electric wheelchairs and scooters. It is an internal vehicle lift that allows the scooter or power chair to be stored inside the user's automobile. The lift has an integrated offset post to help clear the vehicle's bumper, and its base is adjustable to better match the vehicle's dimensions. Its telescoping boom rotates manually, with adjustable length and pitch to allow the user to attach the lifting str

Ameriglide Universal 350 Truck Bed Lift

The Ameriglide Universal 350 Tuck Bed Lift is a scooter or wheelchair loader for pickup trucks designed for use by individuals with mobility disabilities. With the push of a button, this unit can lift almost any mobility scooter or electric power wheelchair into a truck's bed using a boom arm and powered rotation (PR). It can be mounted on either side of the vehicle in most pickup trucks, whether it has an extended bed or an extended cab. Made from weather- resistant materials, the unit has an a

Ameriglide Universal 400 Pr Chair And Scooter Lift

The Ameriglide Universal 400 PR (Power Rotation) Chair and Scooter Lift is a wheelchair and scooter loader designed for use by individuals with mobility disabilities. This lift has a powered rotation boom for loading. It mounts inside the vehicle on either side and has an adjustable base and boom. An integrated offset post ensures that the user's scooter or wheelchair clears the vehicle's bumper. The telescoping boom has adjustable length and pitch that adjusts from 0 to 30 degrees. The unit has

Ameriglide Universal Outside Lift 350

The Universal Outside Lift 350 is a hitch mounted wheelchair or scooter loader designed for use by individuals with mobility disabilities. This lift works with both Class II and Class III hitches, and with most mobility scooters and electric power chairs. The user drives the scooter or wheelchair onto the aluminum platform and secures it in place using the built in retractors. Once the retractors are locked in place, the user pushes a button. The lift. DIMENSIONS: This loader can hold scooters u

Ameriglide Universal Outside Lift 350 Xl

The Ameriglide Universal Outside Lift 350 XL is a wheelchair or scooter loader designed for use by individuals with mobility disabilities. This unit can lift larger electric wheelchairs and scooters with wheelbases up to 48 inches long. Retractors lock the wheelchair or scooter in place. Due to its size, this unit works only with a Class III hitch. The unit comes with a standard Class III hitch receiver. POWER: Uses battery. An optional battery pack is available. OPTIONS: Swing-away arm; scooter

Amerivan

Amerivan is a public transport van designed for use by individuals with mobility disabilities or spinal cord injury. This lowered-floor minivan includes quick-release removable front passenger seating, an optional fold-down middle seat, and enhanced rear seat capacity; a manual fold-out ramp with swing-out gate; non-slip vinyl flooring; and a Q'Straint tie-down belt system (see entries) with two floor tracks for anchoring the belts. The lowered floor is stainless steel, with stainless steel air

Amigo Lift-It

The Amigo Lift-It is an electric, hitch-mounted wheelchair/scooter loader with a built-in control designed for use by individuals with mobility disabilities. The lift is designed to be installed on cars, vans, or trucks with Class II or III receiver hitches and swing-away or hatch-type doors (fold-down tailgates not compatible). No permanent installation is required, and the lift is fully transferable between vehicles. The Lift-It disassembles into four lightweight components when not in use so

Amputee Spinner

The Amputee Spinner is a steering wheel spinner ring designed for use by drivers with a prosthetic upper limb or hook. This device features a large ring that attaches to the rim of the steering wheel. This device can be removed when not required by the driver. WARRANTY: 5 years.

Ams Dodge Caravan Conversion

The AMS Dodge Conversion is a van conversion designed for use by individuals who use wheelchairs. This conversion makes a minivan into a wheelchair-accessible ramp van by completely remanufaturing the van to have a new lowered floor and power ramp system. This enables the wheelchair user to roll up into the van and park in one of several positions, including the driver's position. The conversion can be done for the Dodge Grand Caravan SE, which features anti-lock brakes, dual sliding doors, and

Angelride‚Ñ¢ Infant Car Bed

The AngelRide™ Infant Car Bed is a FMVSS213 approved special needs transportation system for infants with low birth weight. The AngelRide Infant Car Bed comes standard with support and safety features that provide positioning support for infants. Standard features include: five-degree surface to raise the infant’s head for more efficient breathing; patented wrap-around harness for additional protection during a sudden stop or crash; fabric harness that cushions the buckle while allowing quick re

Arboc Low-Floor Bus

The ARBOC Low-Floor Bus is a low-floor bus with a wheehair ramp designed for use by individuals with mobility disabilities. Built on a conventional GM cutaway chassis, this rear wheel drive bus has a manual wheelchair ramp which allows for loading and unloading through the door opening. The bus has a kneeling feature that allows an entrance of less than 5 inches from the curb when the ramp is not deployed. The interior includes theater seating for better viewing for all riders. The bus has a ful

Argo 6X6 Vanguard

The Argo 6x6 Vanguard is an amphibious all terrain vehicle which may be used by persons with lower extremity disabilities due to the vehicles all hand-controlled operation. This 6-wheel drive vehicle may be driven directly from land over water, deep snow, mud, swamp, bog, and bushland. Features include a V-Twin Briggs & Stratton engine, mechanical disc brakes, and all-wheel-drive maneuverability, and skid steering. FRAME: 11-gauge roll-formed steel channel, welded for strength and flexibilit

Argo 8X8 Magnum

The Argo 8x8 Magnum is an all-terrain vehicle designed for use by able bodied individuals and persons with mobility disabilities due to its hand controlled drive and steering. This 8-wheel drive vehicle may be used on rough terrain and dense vegetation, mud, streams, small lakes, deep snow, and ice. Features include a V-Twin Briggs & Stratton engine, mechanical disc brakes, and all-wheel-drive maneuverability, and skid steering. FRAME: 11-gauge roll-formed steel channel, welded for strength

Armstrong Lift

The Armstrong Lift is a powered or manual wheelchair or scooter loader for sport utility vehicles (SUVs)designed for use by individuals with mobility disabilities or spinal cord injury. With the lift in its folded position, the ultra-compact, left-mounted single post design creates 100 percent clear interior floor space, a clearer side view, and allows the rear passenger seats to be fully assembled for use. The side-mount design increases rear bumper clearance for loading and unloading and the a

Atlas Electric Scooter Lift

The Atlas Electric Scooter Lift is a scooter or wheelchair loader for automobile trunks, vans, pickup trucks, and sports utility vehicles. This lift works with either three or four-wheeled scooters and manual or power wheelchairs weighing up to 250 pounds. This loader features a patented Lift'n Latch Boom Arm. The user lifts the arm up and a spring-loaded latch locks the arm in the raised position. Lifting the arm again releases the latch automatically, allowing the arm to be lowered. The contro

Atlas Hitch Lift

The Atlas Hitch Lift is a hitch-mounted scooter loader designed for use in vans or sport utility vehicles with third row seating that is not easily removed or does not fold into the floor. The lift works with three- or four-wheel scooters and manual or powered wheelchairs weighing up to 250 pounds. The rear hitch base assembly mounts to a Class II or III hitch. The swing arm enables the rear hatch door to be used without removing the base assembly. This loader features a patented Lift'n Latch Bo

Auto-Finder

The Auto-Finder is an automobile locator designed for use by individuals with memory or cognitive disabilities. This device enables users to locate a car in a parking lot or multi-level parking deck from up to half a mile away. The unit does not require location marking and provides specific directions that point the way to the car. The system comprises a beacon transceiver that mounts in the vehicle and a pointer remote is carried by the user and attached to a keychain (included). The remote h

Automatic Power Chair Lift (Model Al550)

The Automatic Power Chair Lift, model AL550, is a platform van lift designed for use by individuals with mobility disabilities or spinal cord injury. The lift's docking station features a self-aligning base, enabling the user to drive onto the platform and be locked in place. An audible latching sound is heard as the chair's pin passes into the locking mechanism, and attempting to back the chair verifies that the latch is locked. The docking base also includes a bright colored indicator pin to c

Automatic Van Door Opener (Model V6)

Automatic van door opener operates from switches inside and outside of van. Opens side sliding door. 12 volt DC motor utilizes existing van battery.

Automatic Wheelchair Lock

The Automatic Wheelchair Lock is a wheelchair restraint system for use by people with lower extremity or mobility disabilities, spinal cord injury and others who use a wheelchair. The user can roll forward into the Automatic Wheelchair Lock, which provides a stationary and stable position for a wheelchair during travel. The anchor post for the system mounts to the floor of the vehicle. The restraint bolts to post and hooks to frame of wheelchair. It automatically unlocks at touch of the device's

Autoslide (Model 8100)

The Autoslide, model 8100, is a car transfer aid designed to assist individuals with mobility disabilities in entering or exiting a car. The bottom section of the two-section device is attached to the back of the seat frame using a strong hook and the front is strapped under the seat to prevent sliding. The user sits on the attached top section of the unit and rotates; the top section slides against the bottom section to provide smooth transfers. The small, lightweight unit is equipped with side

Back Up System For Brake (Model V26)

Back up system for brakes provides complete braking capabilities in case of engine failure. Hydraulic operated system is activated automatically in case of engine failure. For use on cars, vans, and small trucks with Drive Master brake systems and factory power brakes. VA accepted.

Back-Saver Vehicle Lift (Model Awl-1600)

The Back-Saver Vehicle Lift, model AWL-1600, is a bumper-mounted wheelchair carrier designed to transport a folding wheelchair on an automobile with limited trunk or interior space. The automatic, motorized lift secures the folded wheelchair against the rear bumper, latching on the arms and supporting the rear wheels (22 inches in diameter or larger) in brackets. The lift includes an emergency safety latch and a state and federally approved license plate holder. CAPACITY: Carries wheelchairs wei

Backup System For Steering (Model V24)

Back up system for sensitized steering provides steering capabilities in case of engine failure. Hydraulically operated system is activated automatically in case of engine failure. For use on cars, vans, and small trucks with Drive Master sensitized steering. VA accepted.

Basement Motorhome Lift (Model 129)

The Basement Motorhome Lift, model 129, is a wheelchair lift without a platform for use on high floor motorhomes and buses with a floor height between 34 and 51 inches. Instead of a platform to support the chair, manual and powered wheelchairs and their occupants are raised and lowered by means of a pivoting arm and a vertical track. The lift requires only 9.5 inches of wall space inside. The lift will not interfere with other people entering the vehicle. Chains with webbed strapping attach onto

Baylift

BayLift is a bus lift designed for use by individuals with mobility disabilities. This compact lift is contained in an enclosure in the luggage bay of the bus. Constructed of steel, the system uses an electro-hydraulic lift with manual backup (hand pump for up, pressure release valve for down). DIMENSIONS (HxLxW): Enclosure is 37 x 18 x 38 inches. Maximum usable platform area is 48 inches long x 29 inches wide. Maximum floor to ground travel is 62 inches. CAPACITY: 600 pounds. WEIGHT: 590 pound

Bifold Ramp

The BiFOLD Ramp is a bus ramp designed for use by individuals with mobility disabilities. This double-folding, underfloor ramp can be installed for front or rear entry on a low-floor bus. The ramp is hydraulically operated with a manual back-up system that requires no valve or switch movement. It has a non-slip surface and stows flat. DIMENSIONS (LxW): Maximum usable platform area is 58.4 x 31.8 inches. CAPACITY: 660 pounds. WARRANTY: One year limited warranty; extended warranty available.

Blind-Drivable Vehicle

---- PROTOTYPE --------- PURPOSE: To create a prototype of a car that can be driven independently by blind and visually impaired individuals. The National Federation of the Blind (NFB) and Virginia Polytechnic Institute and State University, College of Engineering (Virginia Tech) has partnered to demonstrate the first-street vehicle equipped with technology allowing a blind person to drive independently. The NFB Jernigan Institute—the only research and training facility on blindness operated by

Braun 4 Way Power Seat Base

Powered seat base travels 15 inches front to back and 5 inches vertically to allow easy transfer from wheelchair to driver's seat. Accommodates needs of most drivers who can transfer. Operates with push button switch. Installs with 4 bolts. Factory seat or custom driver's seat makes this unit suitable for most vehicles. Switch may be hand held or mounted in convenient location. Seat base measures 34 1/2 inches long by 16 1/2 inches wide and 6 1/2 inches high in low position. Operates with 12 vol

Braun 6 Way Power Seat Base

Powered seat base travels 15 inches front to back and 5 inches vertically to allow easy transfer from wheelchair to driver's seat. Accommodates needs of most drivers who can transfer. Operates with push button switch. Installs with 4 bolts. Factory seat or custom driver's seat makes unit suitable for most vehicles. Switch may be hand held or mounted in convenient location. Seat base measures 34 1/2 inches long by 16 1/2 inches wide by 8 1/2 inches high in low position. Operates with 12 volt DC e

Braun Ambulette

The Braun Ambulette is a van conversion designed for use by individuals with mobility disabilities or spinal cord injury. This van conversion features a Dodge, Ford, or Chevrolet standard length chassis with a 24-inch raised top and a Millennium Series wheelchair lift mounted in either the side or rear door. Two floor plans are available for different combinations of ambulatory seating and wheelchair securement positions. Other features include Braun Fold-A-Way seating, vertical stanchion bar(s)

Braun Built Automatic Swing Door Operators For Rear Post Swing-A-Way Lift

Door operator package to work with swing doors in vans with the rear post Swing-A-Way lift (Chevy and Ford full size vans only). Sequenced to operate with one switch and uses the same peripheral controls as other Braun lifts. Quick release mechanism to freely open the doors in the event of a power failure.

Braun Paratransit Van

The Braun Paratransit Van is a public transportation van designed for use by wheelchair users and other individuals with mobility disabilities. Vans are available with a wide variety of floor plans featuring multiple wheelchair securement locations and seating options. Each van includes an NHTSA-compliant Braun wheelchair lift. Floor plans are available with up to four wheelchair securement positions, with wheelchair and occupant belt systems are included for each securement location. Fold-A-Way

Braun Ra 300 Transit Ramp

The Braun RA300 Transit Ramp is a hydraulic bus ramp designed to provide wheelchair access for a low-floor bus. The ramp comes in a self-contained drop-in unit. When stored, the bi-fold ramp section folds onto itself and then back onto the base. When the ramp is extended, the first section is raised hydraulically and once it passes 90 degrees vertical, it is allowed to lower to its partially extended position using gravity; then the second section uses a similar procedure to reach it fully exten

Braun Ra400 Transit Ramp

The Braun RA400 Transit Ramp is a hydraulic bus ramp designed to provide wheelchair access for a low-floor bus. The ramp comes in a self-contained drop-in unit. When stored, the ramp section folds back onto the base. When the ramp is extended, it is raised hydraulically and once it passes 90 degrees vertical, it is allowed to lower to its fully extended position using gravity. It closes in a similar manner. It has a manual override in case of power loss or malfunction. No pre-assembly is require

Braun Ra400H Transit Ramp

The Braun RA400H Transit Ramp is a hydraulic bus ramp designed to provide wheelchair access for a low-floor bus. The ramp comes in a self-contained drop-in unit. When stored, the ramp section folds back onto the base. When the ramp is extended, it is raised hydraulically and once it passes 90 degrees vertical, it is allowed to lower to its fully extended position using gravity. It closes in a similar manner. It has a manual override in case of power loss or malfunction. No pre-assembly is requir

Braun Tranzsporter

The Braun TranzSporter is a van conversion designed for use by individuals with mobility disabilities or spinal cord injury. This raised top van features an under-vehicle wheelchair lift and a retractable power step. The van is built on a Ford E-350 van chassis with one of three available floor plans. Other features include a Q-Straint belt system, Altro flooring and plywood sub-floor, a lift-step interlock and lift light, Braun-built bench and Fold-A-Way seating, a fire extinguisher, a 10 unit

Braunability Entervan

The BraunAbility Entervan is a side-entry wheelchair accessible conversion of the Dodge Grand Caravan, Chrysler Town & Country, or Honda Odyssey vans. These vans offer a lowered floor, automatic operation of the sliding door, folding ramp, and vehicle kneel, and re-configurable seating that allows the wheelchair or scooter user to drive (if the wheelchair user is able and if vehicle is equipped with hand controls), ride in the front passenger seat, or ride in the 2nd row. The Entervan can ac

Bruno Big Lifter (Model Vsl-570)

The Bruno Big Lifter, model VSL 570, is a wheelchair and scooter loader designed for use at the rear of minivans, sport utility vehicles, and full size vans. The Big Lifter's manual swing has a low-resistance design, requiring minimum strength. Installation requires no structural modification. The adjustable low-profile arm allows the placement of larger power bases into smaller vehicle openings. A Bruno Custom Base provides for mounting the lift in the appropriate location. POWER: Big Lifter is

Bruno Offset Space-Saver (Model Asl-350)

The Offset Space-Saver, model ASL-350, is a trunk-mounted scooter loader designed to load a partially assembled three-wheel scooter in the trunk of a car. The offset design of the lift arm allows the user to position the scooter inside narrow trunk openings. All controls are located on top of the lift arm. The unit disassembles with three steps and can be stored in the vehicle or in the trunk. When an additional tower base assembly is ordered, the loader can be used in more than one vehicle. CAP

Bruno Turning Automotive Seating (Tas) 2400 & 2400E Package

The Bruno Turning Automotive Seating (TAS) 2400 Turnout is a swivel seat base designed for use by individuals with mobility disabilities who have difficulty getting in and out of a car or minivan. The Turnout is installed on a vehicle-specific custom base plate assembly. The swivel base is engineered for ease of installation and use. The seat pivots out and over the door still and is available for both the driver and the passenger side. The 2400 has manual turnourt and the 2400E has powered tur

Bruno Turning Automotive Seating (Tas) 2500 Turny

The Bruno Turning Automotive Seating (TAS) 2500 Turny is a powered turning automotive seat base designed for use by individuals with severe physical disabilities and mobility disabilities who have difficulty entering and exiting minivans, pickup trucks, and full-size vans. The Turny replaces the existing seat base with a swivel, power up and down base. It allows for an even height transfer from a mobility device or can be lowered to 12 or 16 inches. The base swivels manually. The hand control fi

Bruno Turnout Turning Automotive Seating (Model Tas-2400/2400E)

The Bruno Turnout Turning Automotive Seating, model TAS-2400/2400E, is a swivel base designed for use by individuals with mobility disabilities who have difficulty getting in and out of a car or minivan. The unit is installed on a vehicle-specific custom base plate assembly and is available in a manual (TAS-2400) or powered (TAS-2400E) model. The seat rotates out over the doorsill, bridging the gap for a safe transfer onto the seat. Once the user is on the seat, it rotates back into the vehicle.

Buckle Boss

The Buckle Boss is a seat belt lock designed to prevent children with emotional and cognitive disabilities from releasing the seat belt while the car is in motion. Designed specifically to work with seat belts with an upright configuration and a red push-button release, this slotted cover fits over the button and belt receiver slot. The seat belt is inserted into the side slot of the Buckle Boss over the seat belt receptacle and locked in as it normally would be. The Buckle Boss prevents the rel

Buzzard All-Terrain Chair

The Buzzard is an all-terrain wheelchair designed for use by individuals with lower extremity, mobility, or neurological disabilities or spinal cord injury. This all-terrain chair is intended for use in outdoor activities such as hunting, fishing, or getting around rough terrain. FRAME (LxW): Overall dimensions 60 x 36 inches. The chair has a steel frame with monoshock suspension; an optional gun rack is available. The frame is available in any color. UPHOLSTERY: Waterproof mesh upholstery. BRAK

C-Dock

The C-Dock is a wheelchair securement system designed for use by individuals with mobility disabilities or spinal cord injury traveling in vans. This one-piece floor bracket makes the system service friendly. It is equipped with a stainless steel top plate that attaches to the docking unit, providing sturdy protection and stay-open-jaws that provide unlimited exit time. Other features include jam-free latch parts and intuitive interfaces to keep users informed and in control. This device attach

Cable Operated Tractor Brakes.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: To activate the brakes of a White 4-210, 4 wheel drive tractor, for operators with upper and lower extremity impairments. Recommends that a driver's education instruction brake pedal assembly be mounted sideways to the frame of the cab. The operator uses his right hand and shoulder muscles to push the pedal which pulls on a cable connected to the brake pedal on the floor. A flexible sheath carries the cable down to the floor of the cab below the tracto

Camharness (Model 1086)

The CamHarness, model 1086, is a school bus seat restraint designed for use by children with cerebral palsy or severe physical disabilities. This portalble harness-style restraint secures around a bus seat equipped with standard lap-belts (not included). The lap-belt threads through the loops on the harness to secure the passenger. Up to three passengers can fit on a single seat. A chest clip is included. CAPACITY: 30 to 80 pounds.

Car Caddie

The Car Caddie is a car transfer aid designed for use by individuals with mobility disabilities. This figure-eight style aid is constructed of nylon and loops around the car door window frame. The cushioned grip provides security and assistance while entering and exiting the automobile.

Car Door Handle Attachment.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Device increases leverage and gripping surface to open an external handle on a car door. Two versions described, one illustration. Modified gutter clamp is used with a lever and loop extending 7 inches downward from existing handle. Device is easily removable and does not protrude from car door. SKILLS REQUIRED: Metalworking. AUTHOR: Gugerty, J.; Tindall, L. TITLE: Tools, Equipment & Machinery Adapted for the Vocational Education & Employment o

Car Seat Belt Alarm

The Car Seat Belt Alarm is a seat belt alarm designed to alert drivers and caregivers when individuals with dimentia, Alzheimer's Disease, or cognitive disabilities unbuckle seat belts. This device attaches to most automotive seat belts with the included double-stick tape. Once installed, whenever the two pieces of the seat belt are not engaged, the device emits a moderately loud alarm. Rebuckling the seat belt turns off the alarm. COLOR Black.

Car Seat Slide

The Car Seat Slide is a car transfer aid designed for use by individuals with mobility disabilities. The top surface of this mat is made of waterproof nylon to reduce friction and enable smooth turns and sliding while entering or exiting a car. The bottom surface has a non-slip surface to keep the mat in place. The generously-sized hand loops on the sides are made of webbing. DIMENSIONS: The mat is 30 x 35.5 inches and the webbing handles are 1 inch wide.

Car-Go-Mate Scooter Lift (Models Flc-0800-S & Flc-0800-Sb)

The Car-Go-Mate Scooter Lift is a hitch mounted scooter lift designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This exterior scooter lift installs on vehicles with a Class I or Class II 1.25-inch hitch receiver, and can handle scooters with a maximum width of 24.5 inches and a maximum wheelbase of 32 inches. The lift automatically clamps the scooter to the lift platform. It has a lifting range of 28 inches and a locking arm adjustment range of 3

Car-Go-Mate Wheelchair Lift

The Car-Go-Mate Wheelchair Lift is a hitch-mounted wheelchair carrier designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This exterior wheelchair lift installs on vehicles with a Class I or Class II 1.25-inch hitch receiver to hold manual wheelchairs. The wheelchair is automatically clamped to the lift platform, which folds and unfolds with the assistance of a gas-spring counterbalance. The lift is set low to reduce rear vision obstruction. The l

Cares Child Aviation Restraint

The CARES Child Aviation Restraint provides additional support for children with mild to moderate physical disabilities while travelling on an airplane. It can accommodate children from 22 to 75 pounds. The CARES can be used in any seat on the plane excluding the emergency exit rows. The CARES Child Aviation Restraint is a belt-and-buckle device that works with the seat belt on the airplane. The combination of the two provides the same level of safety as a car seat for your child. CARES comes c

Cargo Wedge 250

The Cargo Wedge 250 is a cargo area threshold cover designed for use by people with mobility disabilities who use wheelchairs or scooters. The Cargo Wedge is a large mat made of recycled rubber that overlays a van's or minivan's cargo area to raise the level of the cargo area's floor to the same level as the rear door threshold. The Cargo Wedge can be trimmed with a utility knife or a power saw for a custom fit. It has a non-skid surface. DIMENSIONS (HxLxW): 2.5 x 24 x 48 inches. CAPACITY: 850 p

Cari All

Cari All is a hitch-mounted wheelchair or scooter carrier designed for use by individuals with mobility disabilities. Platform lift mounts to a Class III hitch for transporting powered scooters and non-folding wheelchairs. The lift is unfolded, raised, and lowered with a toggle switch, and folds up automatically when unloaded. Other features include auto-retractable ratchet straps for tie-down; an Integrated Suspension System (ISS) cushions the scooter or powerchair over bumps; a fully boxed bas

Carony Transportation System

Carony is a transport wheelchair base designed for use by individuals with severe physical disabilities or mobility disabilities who have difficulty entering and exiting minivans, pickup trucks, and full-size vans. The system operates in conjunction with a Bruno Turny or Turnout powered seat base. The user glides along a rail from the vehicle seat onto the wheeled base, remaining seated the whole time. A hand control glides the seat out of the vehicle then lowers the seat. The Turny or Turnout p

Carospeed Menox

The Carospeed Menox is a hand control for a motor vehicle accelerator and brake, designed for use by drivers with lower extremity disabilities or spinal cord injury. With this universal floor-mounted hand control, the driver pushes to accelerate and pulls to brake. The control is ergonomic, conforming to the user's natural hand-wrist-arm motion. This unit is recommended for use with automatic gearboxes only, and it can be installed in most vehicles. The Menox needs minimal hardware for installa

Chair Topper

The Chair Topper is a car top mounted wheelchair carrier designed for use by individuals with lower extremity and mobility disabilities, spinal cord injury and others who use a manual wheelchairs. Designed as an overhead wheelchair carrier for compact cars or sedans, this carrier is made of steel, aluminum and fiberglass. It folds, lifts and stores a folding manual wheelchair using power from a vehicle's 12 volt battery. Two switches control the 30-second cycle for stowing and extracting the whe

Classic Hand Control By Veigel (Model 4100Cl)

The Classic Hand Control by Veigel, model 4100CL, is a hand control designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. Designed for right-handed use, the device attaches to the steering wheel. To accelerate, the driver turns the ergonomic handle clockwise. To brake, the driver pushes the unit slightly forward. The brake can be locked while waiting in traffic. The ergonomic handle can be adjusted to accommodate individual driver needs. The unit ca

Classic Hand Control Foam Grip Offset (Model 3500Fx)

The Classic Hand Control Foam Grip Offset, model 3500FX, is a hand control designed to allow individuals with lower extremity disabilities to operate the accelerator and brake of a motor vehicle with one hand. For comfort and added leverage when braking and accelerating, this handle and grip are designed to be two inches longer than most standard hand controls. The offset handle is fully adjustable 360 degrees to provide additional knee clearance for taller users while permitting full accelerati

Classic Hand Control Foam Grip Offset Handle (Model 3501Fbx)

The Classic Hand Control Foam Grip Offset, model 3501FBX, is a hand control designed to allow individuals with lower extremity disabilities or spinal cord injury to operate the accelerator and brake of a motor vehicle with one hand. For comfort and added leverage when braking and accelerating, this handle and grip are designed to be two inches longer than most standard hand controls. The offset handle is fully adjustable 360 degrees to provide additional knee clearance for taller users while per

Classic Hand Control Foam Grip Straight (Model 3500F)

The Classic Hand Control Foam Grip Straight, model 3500F, is a driving hand control designed to allow individuals with lower extremity disabilities to operate the accelerator and brake of a motor vehicle with their hands. The grip and handle are designed to be two inches longer than most standard hand controls to provide more comfortable driving control and added leverage when braking and accelerating.

Classic Hand Control Foam Grip Straight Handle (Model 3501Fb)

The Classic Hand Control Foam Grip Straight Handle, model 3501FB, is a driving hand control designed to allow individuals with lower extremity disabilities to operate the accelerator and brake of a motor vehicle with their hands. The grip and handle are designed to be two inches longer than most standard hand controls to provide more comfortable driving control and added leverage when braking and accelerating.

Classic Hand Control Knob Grip Offset (Model 3500Kx)

The Classic Hand Control Knob Grip Offset, model 3500KX, is a driving hand control designed to allow individuals with lower extremity disabilities to operate the accelerator and brake of a motor vehicle with one hand. For comfort and added leverage when braking and accelerating, this unit comes with a standard bent brake rod that allows the control to be mounted higher in the vehicle for ease in driving.The offset handle is fully adjustable 360 degrees to provide additional knee clearance for ta

Classic Hand Control Knob Grip Offset Handle (Model 3501Kbx)

The Hand Control Knob Grip Offset Handle, model 3501KBX, is hand control designed to allow individuals with lower extremity disabilities or spinal cord injury to operate the accelerator and brake of a motor vehicle with one hand. For comfort and added leverage when braking and accelerating, this handle and grip are designed to be two inches longer than most standard hand controls. This offset handle is fully adjustable 360 degrees to provide additional knee clearance for taller users while permi

Classic Hand Control Knob Grip Straight (Model 3500K)

The Classic Hand Control Knob Grip Straight, model 3500K, is a hand control designed to allow individuals with lower extremity disabilities to operate the accelerator and brake of a motor vehicle with one hand. Designed to ensure comfort and added leverage when braking and accelerating, this unit comes with a standard bent brake rod that allows the control to be mounted higher in the vehicle for ease in driving. A center pivot of our controls allows the grip to be pivoted away from the door for

Classic Hand Control Knob Grip Straight Handle (Model 3501Kb)

The Classic Hand Control Knob Grip Straight Handle, model 3501KB, is a hand control designed to allow individuals with lower extremity disabilities or spinal cord injury to operate the accelerator and brake of a motor vehicle with one hand. Designed for comfort and added leverage when braking and accelerating, this unit comes with a standard bent brake and rod that allows the control to be mounted higher in the vehicle. A center pivot of controls allows the grip to be pivoted away from the door

Collins Allowable Alternate Vehicle - Wheelchair Accessible (Model Cdh12+2)

The Collins Allowable Alternate Vehicle (AAV) - Wheelchair Accessible, model CDH12+2, is a public transport van designed for use by passengers who use wheelchairs. Built on a Chevrolet chassis, the van can carry 12 adult passengers, including two in wheelchairs, and has a four-speed automatic transmission, dual rear wheels, and a six-liter gas tank. It comes with a Braun or Ricon wheelchair lift and either school bus certified or activity seats. DIMENSIONS (HxLxW): 114 x 260 x 95 inches. The wh

Columbia Therapedic Positioning Seat (Model 2000)

The Columbia TheraPedic Positioning Seat, model 2000, is a car seat designed for use in the transport of children with physical and neurological disabilities affecting balance and the ability to sit upright. The seat can be used by children up to 5 feet tall, and may also be used as a wheelchair insert. The unit consists of a vacuum-formed ABS plastic shell with chromed steel side tubes, fire-retardant upholstery, a five-point nylon webbing safety harness, and a nylon webbing supplementary tethe

Compact Hand Control By Veigel (Model 4200Cp)

The Compact Hand Control by Veigel, model 4200CP, is a hand control designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. To accelerate, the driver pulls the ergonomically-shaped handle backwards and a slight push forward operates the brake. The brake can be locked at the push of a button while waiting in traffic. The movements are transferred by sturdy push rods. The special transmission gives increased sensitivity at low revolutions per minute (RP

Companion Seat

The Companion Seat is an adjustable position van seat designed for use by individuals with mobility disabilities. Designed for use with the front passenger seat of Chrysler Town & Country, Dodge Caravan, Plymouth Voyager, and Ford Windstar minivan's, this unit utilizes the van's existing seat but replaces the seat base with a powered seat base. The powered seat base extends the seat a full 20 inches out from the standard seat location and tilts it 6 inches forward. To enter the van, the seat

Conquest Wheelchair Bike

The Conquest Wheelchair Bike is a three-wheeled motorcycle with wheelchair platform designed for use by individuals who use wheelchairs. This vehicle is based on the BMW R-Series motorcycle with a front engine and rear wheel drive. Drivers can roll their wheelchairs onto the vehicle via an automated access ramp. The motorcycle has a reverse gear, and all of its controls are hand operated. Other features include keyless entry; waterproof interior trim; VDO Dayton single CD tuner with 140 watts ma

Covered Outside Lift (Model Al3000)

The Covered Outside Lift, model AL3000, is a hitch-mounted scooter or powered wheelchair carrier designed for use by individuals who use wheelchairs. The plastic watertight cover keeps power chairs and scooters safe while the spring-assisted operation makes the cover easier to open and close. The carrier can be mounted on a class II or III trailer hitch and includes an integrated license plate mount. OPTIONS: Swing-away option. CAPACITY: 350 pounds. WARRANTY: Three-year transferable warranty.

Cp-200 Right Angle Control

The CP-200 Right Angle Control is a hand control for automobiles designed for use by people with lower extremity or neurological disabilities and leg amputees. The CP-200 Right Angle Control is designed for use on any vehicle with automatic transmission, power steering and power brakes. It is made mostly of black anodized aluminum. The unit is equipped for either right- or left-handed use, but that selection must be specified at time of ordering. The CP-200 uses universal mounting brackets and d

Cradle To Hold Bike In The Back Of A Pickup.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Cradle is designed to hold the front tires of two bicycles in a pickup truck but it could also be built to hold the two tires of a wheelchair. Wooden rack made from plywood and dowels. Twin cradles are mounted on a flat piece of plywood that lies on the truck bed. the base can be notched to fit any ribs in the truck bed. Includes photograph and drawing. SKILLS REQUIRED: Woodworking. TITLE: Cradle holds bike in back of a pickup. REF: Article: Sunset Mag

Cross Shaft Extension Control.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Designed for operators who use one hand and may need to relocate the clutch and brake controls to the opposite side. The cross shaft allows an operator to relocate tractor controls to the opposite side. A heavy duty steel rod was inserted into a tube. The ends of the rod were bent at 90 degree angles, and in opposite directions of each other. The rod has a knob to grip at one end. A bolt hole is at the other end for attachment to a linkage. Mounting br

Cruise Control (Model V38)

Cruise control allows operation of vehicle at steady speed without foot on accelerator pedal. Push button or push on handle to activate. Device positioned on dash according to client needs. Inactivate by braking.

Ct-100 Rotary Cable Control

The CT-100 Rotary Cable Control is a hand control for automobiles designed for use by people with lower extremity or neurological disabilities and leg amputees. The Rotary Cable Control may be used on any vehicle with an automatic transmission, power steering, and power brakes. The unit is equipped for either left- or right-handed operation and uses universal mounting brackets. It does not affect operation of the vehicle by people without disabilities. When using the CT-100, the user operates th

Curb-Sider (Model Vsl-6000)

The Curb-Sider, model VSL-6000, is a trunk-mounted wheelchair alternative loader for persons with physical disabilities needing to transport power wheelchairs or scooters. This fully-powered lift fits most types of vehicle, including minivans, SUVs, CUVs, pickup trucks, and full-size vans. It is available for either the passenger or driver side, and its offset arm can pick up wheelchairs or scooters from the rear of the vehicle, from the rear corner, or from the side of the vehicle (near the rea

Customized Hand Controls

The Customized Hand Controls are a driving control system designed for use by people with lower extremity or neurological disabilities or spinal cord injury to use only their hands to operate automobiles, trucks, self-propelled lawn and garden equipment (including riding lawn mowers), and farm vehicles (including tractors). Each set of controls is individually developed for a user. The controls can be applied to the clutch, brakes, throttle and any other function of the vehicle. They can be int

Cycle Rack

CUSTOM ADAPTATION PURPOSE: To enable an individual who uses a hand-propelled cycle wheelchair to transport it to cycling trails. A solution was developed that enables the individual to load the cycle, one end at a time, from his wheelchair onto a rack attached to a hitch on the back of his car. A short tubular bracket was attached transversely to the frame of the cycle at the center of gravity. A carrier pin was mounted to project horizontally from the hitch bracket; the pin engages with the tu

Dadc 500 Manual Push Pull

The DADC 500 Manual Push Pull is a hand control designed for use by individuals with mobility disabilities, spinal cord injury, or upper extremity disabilities, including limited range of motion. It is designed for drivers who like the traditional push/pull handle. The user pulls the handle to control the accelerator and pushes it to apply the brakes. The DADC 500 Manual Push Pull features quick, light action and smooth response to the user's motions. It fits a wide range of vehicles with little

Dadc 500 Manual Push Rock

The DADC 500 Manual Push Rock is a hand control designed for use by individuals with mobility disabilities, spinal cord injury, or upper or lower extremity disabilities, including limited range of motion. Designed for drivers who want a higher hand position on the steering wheel, the DADC 500 Manual Push Rock features a vertical handle and provides a quick, light action and smooth response to the user's motions. The user pulls (or rocks) the vertical handle back to control the accelerator and pu

Dadc 500 Push Pull Hand Control

The DADC 500 Push Pull is a hand control designed for use by individuals with mobility disabilities, spinal cord injury, or upper extremity disabilities, including limited range of motion or hand strength. The user pulls the handle to control the accelerator and pushes it to apply the brakes. Designed for drivers who like the traditional push/pull handle, the DADC 500 Push Pull is vacuum assisted and requires only a light touch to operate. The full range of motion from idle to full throttle is l

Dadc 500 Twist

The DADC 500 Twist is a hand control designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury, including people with limited range of motion. This power assisted hand control has a handle that is twisted gently for gas and a lever that is pushed for brakes. The DADC 500 Twist is intended for drivers who want ease of operation and precise, fingertip control. Its vacuum-assisted, motorcycle-style handle enables full throttle in one quarter turn of the wri

Dadc Brake Only

The DADC Brake Only is a hand control designed for use by individuals with mobility disabilities, spinal cord injury, upper or lower extremity disabilities, including limited range of motion or use of only one leg, or drivers who can operate the pedals, but are challenged with the transition from gas to brake. The user pushes the control's handle to apply the brakes. It does not connect to the accelerator. The DADC 500 Brake Only provides a quick, light action and a smooth response. It fits a wi

Dadc Key Tee

The DADC Key Tee is a key holder designed for use by individuals with grasping disabilities, limited hand strength or arthritis. This T-shaped holder fit over the top of most keys to facilitate grasping the key and increase leverage when turning the key.

Dadc Turn Signal Adapter

The DADC Turn Signal Adapter is a right or left hand directional signal extension lever designed for use by individuals with upper extremity disabilities, especially those with limited or no use of the left hand or arm. Designed to allow drivers to operate the turn signals with the right hand instead of the left, this device attaches to the turn signal lever and crosses to the right side of the steering column. It can also be mounted on the left side as an extension of the turn signal lever. The

Decpac Multipurpose Ramp (Model Mp44)

The Decpac Multipurpose Ramp, model MP44, is a portable ramp designed for use to provide access to vans or steps for individuals with mobility or lower extremity disabilities or spinal cord injury. This four-panel folding ramp can be used for a rise up to 13 inches over steps at home or to enter the side of a minivan. When folded it can fit into a van and slide under a seat. The ramp is constructed from laminated fiberglass. The top surface has a textured non-slip tread and the edges are marked

Decpac Multipurpose Ramp With Edge Barrier (Model Mpeb44 )

The Decpac Multipurpose Ramp with Edge Barrier, model MPEB44, is a ramp designed for use by individuals with mobility or lower extremity disabilities or spinal cord injury. It is a four-panel folding ramp with side barriers to help keep a wheelchair, scooter or stroller on the ramp. This ramp can be used for entryways with steps or to enter or exit a minivan on the side. The ramp can be used for a rise up to 13 inches. When folded the ramp can fit in a van and slide under a seat. The ramp is mad

Decpac Multipurpose Ramp With Edge Barrier (Model Mpeb55)

The Decpac Multipurpose Ramp with Edge Barrier, model MPEB55, is a portable ramp designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This collapsible four panel ramp can fit a rise of up to 16 inches. It fits in the side of a minivan, but when folded is compact enough to store under the seat of the van. Constructed from laminated fiberglass. its top surface has a textured non-slip tread and the edges are marked with a caution stripe. The top edge

Decpac Multipurpose Ramp With Edge Barrier (Model Mpeb66)

The Decpac Multipurpose Ramp with Edge Barrier, model MPEB66, is a portable ramp designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This ramp can accommodate a rise of up to 20 inches, and it can be used for van access. Constructed from laminated fiberglass, its top surface has a textured non-slip tread and the edges are marked with a red caution stripe. Edge barriers are included for safety. The top edge is indicated with a label and it has a th

Deep Dish (Small) Steering Wheel (Model V14)

Deep dish steering wheel brings steering wheel rim 4 inches closer to wheelchair driver. Smaller diameter of steering wheel improves wheelchair accessibility to steering wheel and lessens range of motion need for steering. Diameter of wheel 13 1/2 inches. Usually used with sensitized steering system (see separate entry) and with backup system for emergencies in case of engine failure.

Deluxe Adjustable Key Holder (Model 6513)

The Deluxe Adjustable Key Holder, model 6513, is a key holder designed for use by individuals with grasping disabilities, limited hand strength or arthritis. The device consists of a plastic frame that provides adjustable tension so position of keys can be held at the most desirable angle. Other features include a leather loop that is late free and holds up to five keys.

Digipad-Ii Econo Series Touchpad

The Digipad-II Econo Series Touchpad is a driving control system designed for use by individuals with upper extremity disabilities. It can be configured for almost any make or model of vehicle. The touchpad can be used to access 15 commonly used vehicle functions: ignition; start; intermittent, low and high wipers; wiper wash; park lights; headlights; low, medium, and high front fan speeds; cruise on; cruise set; park brake; and one additional auxiliary function. Access to these 15 functions is

Digital Shifter

The Digital Shifter is a computer-controlled driving system designed for use by individuals with upper extremity disabilities. The system allows a person having limited hand/arm strength and range of motion to shift an automatic transmission. The Digital Shifter is microprocessor-controlled and interfaces with most vehicles by dip switch selection. The system comes with the ACE Digital Shifter, the ACE Digital Shifter Actuator and Customer Interface switches. In positive shifting with one press

Digitone Audible Switching Device

The Digitone Audible Switching Device is a driving control system designed for use by individuals with physical disabilities. This device enables the driver to activate up to eight vehicle functions using one switch. Functions that can be activated include turn signals, horn, dimmer, wiper speeds, wiper wash, cruise on, and cruise set. When the switch connected to this device is depressed, the device begins emitting a series of eight different tones of a musical octave, each of which is assigned

Digivoice

Digivoice is a driving control system designed for use by individuals with upper extremity disabilities. This system allows voice operation of up to 16 vehicle controls such as shifter functions, turn signals, horn, headlight dimmer, and wipers. The driver touches a single telco-style ACT switch (not included) to activate the system. When the switch is depressed, the system says "READY" and the driver speaks the name of the desired function into the supplied microphone. The function is then acti

Diy Kinetic Photovoltaic Vehicle (Kpv)

---- DO IT YOURSELF ENTRY --------- PURPOSE: To create a do-it-yourself easily transportable solar-electric two-wheeled scooter for use by individuals with mobility disabilities. Working as an engineer on a Canadian schooner, Terry Hope, found himself in need a solution to bring aboard an electric scooter that could fit in a suitcase. A stock steel scooter frame is augmented with a variety of hand-made and off-the-shelf parts. The end result is home-built solar-electric Kinetic Photovoltaic Veh

Door Knob Lever

Steel handle designed to attach to most car door levers. Allows person with weak hand grip to turn a door lever. Consists of two pieces which screw together, open end allows insertion of car door handle. 1 year parts and labor warranty.

Doron L-300 R/a

The Doron L-300 R/A is a simulated training driving aid system for persons with diabilities. It creates a realistic substitute for on-street driving, helping the driver to develop the ability to recognize, analyze and correctly respond to traffic situations. The system may be motified for hand controls and wheelchair accessiblity. This driver training system consist of three elements. First, an instructor console, with full color monitor, and a selectable touch screen display. The IBM compatible

Doze Alert Driver Sleep Alarm

The Doze Alert Driver Sleep Alarm is a driver head position alert device designed to warn drivers when they are falling asleep at the wheel. Worn behind the ear, the device buzzes loudly (86 decibels) when the wearer's head falls forward. POWER: Uses a button cell battery (included). WEIGHT: 0.5 ounce.

Dreamfit Motorcycle

---- PROTOTYPE --------- PURPOSE: To design a prototype of a motorcycle that can be used by individuals with paraplegia. Inspired by a paraplegic ex-motorcross champion, West Australian Darren Lomman established a project to create a motocycle for paraplegic riders based on a heavily modified Honda CBR250RR. The prototype is road licensed and operational and has the potential to become a commercial product. Started as a university project, the Dreamfit CBR250RR has been modified to suit riders p

Drive Master D13 Foot Steering Kit

Foot steering control kit transfers driving functions normally operated with hands to foot control for persons who have insufficient strength in their upper extremities to drive. A system of metal plates and associated equipment is mounted on floor of vehicle according to driver' s needs. System moves to activate various driving functions. Auxiliary and secondary vehicle controls also adapted to foot operation. Comfortable shoe of driver's choice used with system.

Drive Master D1Xl Auto Hand Control

Hand control, push toward floor to brake and pull parallel to steering column for acceleration. Attaches to either side of steering column. Recommended for use in vehicle with power steering and power brakes. Stainless steel and aircraft aluminum parts are rustfree. Nonglare surface finish. Hand control does not interfere with operation of vehicle by able bodied person. Tilt type and telescoping steering wheels do not interfere with proper use of hand control. Easy to install. Instruction and di

Drive Master D2 Dimmer Switch & D7 Special Dimmer Switch

Dimmer switches allow hand operation of headlight dimmer. D2 ($42) dimmer switch mounts on hand control with bracket; D7 ($45) mounts on directional signal handle. Dimmer raises or lowers headlight beam on touch of button.

Drive Master D21 Electronic Directional Signal

Electronic directional signal allows drive weak arms to use directional signal at touch of switch. Device converts directional signal from manual to electric and requires less effort for operation. Price includes installation in American cars or vans.

Drive Master D3 Horn Button

Horn button mounts on hand control handle and allows driver to operate horn without removing hand from control. Button switch.

Drive Master D5 Quad Handle For Hand Control

Quad hand control grip attaches to Drive Master Hand Control (see separate entry) to provide adaptation of regular hand control for quadriplegic who has little wrist or hand strength. L shaped wrist support attaches to conventional hand control. Used with dimmer switch ( D2, see separate entry) and Horn button (D3, see separate entry). Use only with Drive Master hand controls.

Drive Master D9Xl Auto Hand Control For Brake Only

Hand control for brake. Push mechanism operates unit. Suitable for use with brake pedal for persons with enough strength in right leg to operate accelerator.

Drive Master Directional Signal Extension (Model D15)

Directional signal extension lever allows left hand operation of directional signal. Aluminum extension bolts onto vehicle directional signal to allow operation of signal device with left hand.

Drive Master Drop Floor (Models V10Bf & V10B3)

Drop floor in van permanently lowers floor of van 4 to 6 inches for the width of the van and from the side or back door of van into driving and/ or passenger area. This provides proper visibility for wheelchair occupant whose head is more than 47 inches from floor when seated. This van modification requires structural modification to van; chassis of van is cut and reinforced. Not available for Dodge vans.

Drive Master Electronic Directional Signal (Model V29)

Solid state plug in unit affords easy operation of directional signals. Push button operation. Buttons can be located to accommodate drivers limitations. Available for all cars, vans and trucks.

Drive Master Fill In Passenger Step Of Van (Model V10D)

Fill in of passenger step of van provides levels surface for movement of occupant in wheelchair. If step is not filled in and wheelchair moves over it, chair will tip over.

Drive Master Foot Steering (Model V31)

Custom fitted floor mounted disc attaches to existing steering column near the floor and offers complete steering capability. Brake and accelerator are operated as usual with right foot. Left foot operates disc at level of brake pedal and to the left of it with circular motion but in same motions as steering wheel. Comfortable shoe of operators choice is permanently attached to unit.

Drive Master Hand Control (Model V8)

Hand control, aluminum and stainless steel construction. Control attached to steering column, brake and accelerator pedals. Fits American and imported vehicles. Control level extends under steering column and upward to about the level of factory installed directional signal. Bolt attachment to gas pedal and accelerator. Pull to accelerate; push for brake. 30 day guarantee of full refund. Easy to install; no parts go under the hood of the vehicle. Shipped with instructions and diagrams. Will not

Drive Master Horizontal Steering Column (Model V42)

Horizontal steering column replaces original factory steering column in vehicle and places it near or in lap of driver in wheelchair. Eliminates the necessity to raise the arm in order to reach standard steering column. Vehicle or van usually has sensitized steering and sensitized brakes with hydraulic backup system that automatically actuates in case of engine failure.

Drive Master Interchangeable Driver Or Passenger Seat (Model V17)

Quick release seat for van allows seat to be put in place for use by driver other than wheelchair occupant. Change of seats done by able bodied person. Seat provided with storage lock for back part of van. Seat can be used in stored position as well as in driver or passenger position. Easy to move by rolling on casters.

Drive Master Left Hand Gear Selector (Model D8)

Aluminum extension lever to enable driver to operate gear selector with left hand instead of right hand.

Drive Master Little People Adjustable Pedals (Model D12)

Pedal extensions both to gas and brake pedal actuating rod (under pedal) and floor (for support); folds down (after pulling pin) when not in use by driver. Fabricated of aluminum. Extends pedals 6 to 10 inches.

Drive Master Low Effort Brakes (Model V16)

Sensitized brakes reduce the effort needed to operate power brakes on vehicle. Modification is made on factory installed power brake system. For persons who have difficulty operating factory installed power brake system. VA accepted.

Drive Master Low Effort Steering (Model V15)

Low effort steering reduces the effort to steer the vehicle 41 percent. Factory steering box or rack is modified at Drive Master factory and installed in vehicle. A backup system can be purchased separately. Price quoted for American made vans.

Drive Master Mini Console (Model V11)

Driving control system positions secondary (ignition) controls and auxiliary (wiper, etc.) controls from dash board of vehicle at driver's right. Toggle switches for auxiliary controls, and key switch to turn for ignition. Flip switch for wipers. Operates with minimum of effort. Typical control box approximates size of standard hard back book.

Drive Master No Effort Brake (Model V25)

No effort brake requires only a few ounces of force to operate power brake. Replaces factory installed unit, available for car, van and light trucks. Adds no visible components to vehicle. Backup system available (see separate entry).

Drive Master No Effort Steering (Model V23)

No effort steering reduces the effort required to steer a vehicle by up to 70 percent. Factory steering box or rack is modified at Drive Master factory and installed in vehicle. Unit adds no visible components to vehicle. Backup system is available separately. VA accepted. Price quoted for full size American vans.

Drive Master Parking Brake Handle (Model D4)

Stainless steel lever attaches to foot operated parking brake to adapt it to hand use. User needs grip sufficient to operate regular brake and lever. Handle can be bent somewhat at time of installation to achieve proper angle for individual needs.head of lever has rubber grip similar to that of bicycle handle. Client needs strength in hand approximately the same as that in the left foot with which able bodied driver operates standard foot parking brake.

Drive Master Power Floor Pan (Models V10A1F & V10A2C)

Specially designed elevator in driver area to accommodate wheelchairs, will lower floor up to 6 inches to allow complete peripheral vision while driving. Available for Chevrolet and Ford sized vans. Designed for people to drive from their wheelchairs.

Drive Master Powered Parking Brake (Model V19)

Powered parking brake is a special designed motor offering complete control of power brake by manipulation of a toggle switch. Available on cars, vans and trucks. Warning lamp alerts driver that brake is in the on position.

Drive Master S5 Molded Plastic Quad Cuff

Molded plastic quad cuff steering spinner provides rigid support for wrist and hand. For persons lacking tensor control and need wrist support. Attaches securely to steering wheel with ball bearing cast aluminum base. No locking pin; hand can be lifted out if necessary. Driver must be able to position hand in devices. Fastens around arm with velcro prethreaded through loop. Slight pressure secure hand and wrist in place.

Drive Master Swinger Lift (Model V1A1)

Fully automatic rotary lift; operates from switches on chest high security rail with optional switches on van console or outside switch box; automatic safety stop; constructed of aluminum and steel; operates from van battery; requires less than 3 feet outside clearance. Dimensions of lift at largest point are 24 by 34 inches. Lift can be used on side of van only. Safety backup system. VA accepted.

Drive Master V13 Extended Steering Column

Extended steering column brings steering wheel 2 to 6 inches closer to wheelchair driver. For quadriplegic with limited range of motion who needs steering wheel closer to wheelchair or for wheelchair occupant with need for extra leg room under steering column.

Drive Master V21 Powered Windows

Power windows are installed within door of vehicle and operate at touch of switch. User must have enough strength to push button or lever. Necessary with wide or electric wheelchairs. For two front windows of full size American made vans.

Drive Master V28 Powered Gear Selector

Powered gear selector allows driver with upper extremity disabilities to shift gears with toggle switch. Toggle switch positioned according to client needs but usually on Command Post Console (see separate entry). Push/pull switches available as option.

Drive Master V30 Custom Switch Location

Custom switch location according to needs of client. Toggle and some push/pull switches available. All switches necessary for driving can be custom positioned if needed.

Drive Master V33 Raised Side Door Opening

Raised van door facilitates accommodation of wheelchair user who is very tall or who has limited movement. White fiberglass to match Drive Master Raised Roof (see separate entry). Sizes for full, mid size and sport top offer 57 inches of head clearance for full and mid size, 53 inches for sport top.

Driver Master D14 Gear Shift Extension

Gear selector extension lever provides more leverage for disabled persons in shifting gears. Left hand extension lever attaches to conventional gear shift at 90 degree angle on left side slightly above factory installed directional signal. Approximately same size as standard gear shift or directional signal. For vehicles with automatic transmission only.

Driver Side Transfer Seat By Veigel (Model 4500)

The Driver Side Transfer Seat, model 4500, is a car transfer aid designed for use by people with lower extremity or mobility disabilities or spinal cord injury and others who use wheelchairs and drive automobiles. Designed to assist a car driver who uses a wheelchair when transferring into and out of an automobile, this padded seat bridges the gap between the wheelchair and the driver seat. The padded seat can be removed or folded when not in use.

Driver's Alert Glasses

Driver's alert glasses are designed for individuals who may need help staying awake while driving. Should user become drowsy and nod off, they sound a warning alarm when user lowers head. Yellow-tinted lenses reduce glare and help user to see better in low light. Can be used with or without the alarm. MATERIALS: polycarbonate frames. COLOR: Black. SIZE: Measures approx 5-3/4 inches lens to lens. Arms approx 5 inches L X 7/8 inches H.

Dual Brake For Driver Training (Models V37 & D18)

Dual brake for driver training allows driving instructor to brake vehicle in case of misjudgment or emergency. Necessary in all driver training vehicles.

Eagle Single Rider Vehicle With Standard Seat

The Eagle Single Rider Vehicle with Standard Seat is an adapted golf cart and personal electric vehicle designed for use by individuals with walking or balance disabilities, arthritis or limited stamina. This single rider golf car allows the user to play golf without getting out of the cart. When the user approaches a golf ball, he or she can position the vehicle, put it in “park,” and then rotate the seat and hit the ball while seated. The frame/chassis is made of welded tubular painted steel a

Eagle Single Rider Vehicle With Tilt Seat (Model 724Ts)

The Eagle Single Rider Vehicle with Tilt Seat, model 724TS, is an adapted golf cart and personal electric vehicle designed for use by individuals with walking or balance disabilities, arthritis or limited stamina. This single rider golf car allows the user to play golf without getting out of the cart. When the user approaches a golf ball, he or she can position the vehicle, put it in “park,” and then rotate the seat and hit the ball while seated. The frame/chassis is made of welded tubular paint

Easy Key Turner (Model En15Crd)

The Easy Key Turner, model EN15CRD, is a key holder designed for use by individuals with limited grasping ability or hand strength. These large T-shaped holders fit over the top of the key and have a D-shaped opening on each side for ease in grasping. The turner provides a large grasping surface and leverage for turning the key. DIMENSIONS (HxDxW): 1.25 x 0.25 x 2.25 inches. COLOR: Two different colors per package.

Easy Reach

The Easy-Reach is a van lift designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This lift seat allows the original seat of a truck, SUV, van, or minivan to swivel out of the vehicle and lower to wheelchair height. The user then transfers from the chair to the vehicle seat, and presses a button to be lifted into the vehicle. The lift extends from the vehicle at an angle matching that of the door. A manual back-up system in case of vehicle power fa

Easy Reach Seat Belt Handle

The Easy Reach Seat Belt Handle is a seat belt extension handle designed for use by individuals with upper extremity disabilities or arthritis. This lightweight device is made of a ethylene methyl acrylate resin and snaps on to the seat belt to create an expended grip. The device glows in the dark to aid in locating it. 

Easy-Transfer

The Easy-Transfer is a car transfer aid designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This flip-down transfer seat acts as a bridge between a wheelchair or scooter and a vehicle seat. It attaches to the vehicle and can be stowed when the user is driving or when the car is used by other drivers or passengers. There are three levels of stowage: Flip-up to remain vertical between the car seat and the car door, detach and stow behind the car sea

Ecovehicle Sledgehammer Series

The EcoVehicle is a personal electric vehicle designed for use by individuals with walking or balance disabilities or arthritis or limited stamina. This lower-speed vehicle does not require a driver's license for most applications. The frame and body panels are made of diamond-plate steel. All parts are protected against corrosion. Features include handrails on the outside, additional grab-handles inside, headlights, taillights and turn signals, seat belts, automotive safety glass windshield and

Elaine Anne Lift System

The Elaine Anne Lift System is a wheelchair lift for a pickup truck or sport utility vehicle designed to enable drivers who use wheelchairs to enter and drive the vehicle while remaining in the wheelchair. This lift is available for Chevrolet Suburbans, Avalanche, and Tahoe; General Motors Yukon, Yukon Denalie, and Yukon XL; and Cadillac Escalade, Escalade EXT, and Escalade ESV. It is also available for the Hummer and Chevrolet and General Motors pick-up trucks with crew or extended cabs (0.75-,

Elderstore Extra Lightweight Folding Transport Chair

The Elderstore extra lightweight folding transport chair is designed for use by the elderly or users who have difficulty getting out of the car, a wheelchair, or any other sitting situation. Comes with a carry bag and folds up for storage. The armrests are padded for comfort and can be flipped out of the way as an option.

Electric Carrier & Carrier Cover Package (Models Wc210M-52 & Wc211M-52)

The Electric Carrier, model WC210M-52, is a Class 3 hitch mounted carrier for scooters or power wheelchairs. The lift is equipped with an electrical-operated screw jack that is activated by a switch. The power unit comes with a single wire that can be attached directly to the vehicle's electrical system or wired to a trailer plug. The power unit has built-in night lights which are switched on and off with a hidden push button under the red access cap. An emergency crank is also supplied to lower

Electric Cart Carrier

The Electric Cart Carrier is a hitch-mounted scooter carrier. This unit attaches to any vehicle with a class III hitch receiver and carries up to 500 pounds. It contains no wheels, axles, or hydraulics, which eliminates the need for special permits or licenses. The box-style unit has a lightweight extruded aluminum framework and a waterproof plywood floor. The unit has two retractable, stabilizing legs for use during loading and unloading and a ramp which doubles as a safety gate. It is equipped

Electric Holdown (Model 128)

The Electric Holdown, model 128, is wheelchair restraint system that may be installed for the driver or passenger wheelchair position. (Installation depends on the underside of the van.) The holdown consists of two pieces: one piece hooks to the wheelchair frame behind the casters, and the second mounts into the floor of the van. The floor mounted piece clamps onto the piece attached to the chair. The control switch mounts to the vehicle's dashboard or the most convenient position for the operat

Elite G2

The Elite G2 is a scooter or wheelchair loader for a van designed for use by individuals with mobility disabilities. This loader features a keychain remote control, a drive on/drive off platform, and quick cycling efficiency. DIMENSIONS: The platform is 44 x 27.5 inches. Stowed, the lift is 50 x 44 x 29.5 inches. CAPACITY: 350 pounds. WEIGHT: 200 pounds. COLOR: Available in five colors.

Equalizer Van Lift (Models Flc-0300-M25, Flc-0300-M40, Flc-0300-P25, Flc-0300-P40, Flc-0300-E25, & Flc-0300-E40)

The Equalizer Van Lift is a van or pickup truck wheelchair lift designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This powered lift adapts to most mini-vans, full sized vans, SUVs and pickup trucks, and fits other specialty vehicles such as the Chrysler PT Cruiser. It has a rotation range of 200 degrees. Equalizer 1 (FLC-0300-M25, FLC-0300-M40) is a power lift with manual rotation. Equalizer 2 (FLC-0300-P25, FLC-0300-P40) is a power lift with p

Excel & Excel Compact

The Excel & Excel Compact are wheelchair or scooter loaders vans designed for use by individuals with mobility disabilities. This boom lift features a wireless keychain remote control. DIMENSIONS: The vertical reach is 35.5 inches and the boom length is 38.25 inches on both models. The total height for the Excel is 39.25 inches and 31.75 inches for the Excel Compact. CAPACITY: 350 ponds on both models. WEIGHT: The installed weight for the Excel is 66 pounds and 64 ponds for the Excel Compact

Excel 200

The Excel 200 is a scooter or wheelchair loader designed for use by individuals with mobility disabilities. With five adjustments available to the dealer, this lift fits in most SUVs, minivans, station wagons, and the PT Cruiser and accommodates most scooters and lightweight powered wheelchairs. This lift offers both rear and curbside loading and the dual positioning base makes installationpossible on either the passenger or the driver's side of the rear cargo area. The Excel 200 lifts the po

Excel E & Excel E Compact

The Excel E & Excel E Compact are wheelchair or scooter loaders vans designed for use by individuals with mobility disabilities. This manual swing boom lift features push-button controls and adjustable locking "stops." DIMENSIONS: The vertical reach is 35.5 inches and the boom length is 38.25 inches on both models. The total height for the Excel is 39.25 inches and 31.75 inches for the Excel Compact. CAPACITY: 350 ponds on both models. WEIGHT: The installed weight for the Excel is 54 pounds

Express Ramp

The Express Ramp is a ramp for a rail car designed for use by individuals with mobility disabilities. When deployed, this stainless steel ramp bridges the gap between the rail car door and the station platform. When not in use, it stows in an unobtrusive vestibule in the floor of the rail car. The ramp's operation is fully automatic using a drive system that is compatible with existing rail car controls. Manual backup operation is also available. DIMENSIONS (LxW): Maximum usable bridgeplate area

Extended Clutch Pedal Surface With Rolled Edges.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: To prevent foot slippage from clutch pedal surface due to impaired control of left leg. A piece of perforated flat iron is fastened to the original pedal using a standard hose clamp. The left and right side are rolled upwards to help prevent foot from sliding off pedal. The editor recommends bolting the flat iron to the pedal for greater reliability. SKILLS REQUIRED: Metalworking. AUTHOR:Field, W.E. TITLE:Agricultural Tools, Machinery & Buildings f

Extension Control Key Extension (Model 3560)

The Extension Control Key Extension, model 3560 is a key holder designed for use by individuals with grasping disabilities, limited hand strength or arthritis. Designed to provide assistance in turning vehicle ignition switches, the adjustable extension attaches to a single key.

Extension Control Park Brake Extension (Model 3541)

The Extension Control Park Brake, model 3541, is a parking brake extension lever designed for use by individuals with lower extremity disabilities or spinal cord injury. The handle is bolted to the foot-operated parking brake for hand operation. The device is operated by pushing toward the floor. The handle folds out of the way for storage. The device is made of a lightweight, brushed aluminum alloy. WARRANTY: Limited 2 year warranty applies only to vehicles with power brakes, power steering and

Extension Control Park Brake Extension (Model 3542)

The Extension Control Park Brake Extension, model 3542, is a gear selection lever for use on vehicles with automatic transmission designed to accommodate and provide extra leverage for persons without the use of either their right or left hand or arm. It attaches to the right or left side of the steering wheel.

Extension Control Right Hand Turn Signal Lever Extension (Model 3543)

The Extension Control Right Hand Turn Signal Lever Extension, model 3543, is a directional signal attachment designed to allow drivers to operate the turn signals with the right hand instead of the left. This lightweight crossover lever allows the user to operate the turn signal with ease. The device attaches to the turn signal lever and crosses to the right side of the steering column. It is installed using bands rather than screws, leaving the vehicle’s interior in its original condition.

Extension Handles For Control Knobs.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Designed for persons with limited mobility and reach, adaptors and extension handles can be used to control electrical equipment and key switches. Long extension handles can be made from sections of steel tubing with two notches cut out on one end and a crosspiece welded to the other to form a 't" handle. Short pieces of rubber heater hose are clamped onto the control knobs of electrical equipment, such as a car radio or air conditioner. To operate the

Ez Lock

Floor mounted wheelchair restraint system secures wheelchair to floor of van. V.A. accepted. Enables user to sit forward facing or in an angled position in van. Wheelchairs can be rolled into the receiver lock mechanism by backing in or by forward entry. Safety warning signal will sound when vehicle is running while the lock is not fully set. Available with many different "H" bracket configurations to fit most manual and powered wheelchairs on the market. Warranty available.

Ez Rider Low Floor Transit Bus

The EZ Rider Low Floor Transit Bus is a wheelchair-accessible bus designed for use by individuals with mobility disabilities or spinal cord injury. This low-floor bus has an electric paratransit ramp at the front and/or center door. Standard floorplans include 20 or 23 seats with space for two wheelchairs. Other features include integral welded monocoque construction; Cummins B5.9L or C8.3L turbo diesel or natural gas engine; and a cradle-mounted engine and transmission for ease in maintenance.

Ez Rider Transport Stroller, Ez12T-New Cordura Fabric

EZ Rider Transport Stroller is designed for the less involved person with some upper body control. It has been satisfactorily crash-tested at 30 mph, 20 g deceleration in a forward facing configuration using the EZ Rider Transport stroller's 5-point tie down harness. The New Cordura Fabric is a lightweight, compact-folding push chair that folds like an "umbrella" style stroller. It is designed to promote an upright posture with support, adjustable seat depth, adjustable height swing-away foot

Ez-Access Suitcase Advantage Series Ramp (Models As2, As3, As4, As5 & As6)

The EZ-ACCESS SUITCASE Advantage Series Ramp are portable single-track wheelchair and scooter ramps designed for use by people with mobility disabilities. These ramps are made of welded aircraft-grade aluminum and feature an applied skid-resistant surface with reflective stripes on each side of the surface. Each ramp has a self-adjusting bottom transition plate. These ramps are recommended for use over curbs and steps and to enter some minivans (models AS5 and AS6) and sport utility vehicles (AS

Ez-Access Suitcase Ramp (Models 2, 3, 4, 5 & 6)

The EZ-ACCESS SUITCASE Ramp is a portable single-track wheelchair and scooter ramps designed for use by people with mobility disabilities. Th1s ramp is made of aluminum and features an non-skid driving surface. The ramp is designed for use over curbs and steps and to enter some minivans (models 5 and 6) and sport utility vehicles (model 6 only). Each ramp has a fold-in-half design for compact portability, and a built-in carrying handle. DIMENSIONS (LxW): 24 x 29 inches (model 2); 36 x 29 inches

Ez-Access Suitcase Signature Series Ramp (Models Ss2, Ss3, Ss4, Ss5, Ss6, Ss7 & Ss8)

The EZ-ACCESS SUITCASE Signature Series Ramps are portable single-track wheelchair and scooter ramps designed for use by people with mobility disabilities. These ramps are made of welded aircraft-grade aluminum and feature an applied skid-resistant surface. Each ramp has a self-adjusting bottom transition plate. These ramps are recommended for use over curbs and steps and to with some minivans, vans and sport utility vehicles. Each ramp divides into two halves by removing two hinge pins, and whe

Ez-Access Trifold Advantage Series Ramp (Models As5, As6, As7, As8 & As10)

The EZ-Access Trifold Advantage Series Ramp is a portable single-track wheelchair and scooter ramps designed for use by people with mobility disabilities. These ramps are made of welded aircraft-grade aluminum and feature an applied skid-resistant surface with reflective stripes on each side of the surface. Each ramp has a self-adjusting bottom transition plate. These ramps are recommended for use over curbs and steps and to enter some minivans and sport utility vehicles. Each ramp divides into

Fds Transportable Hand Control

The FDS Transportable Hand Control is an automobile hand control designed for use by individuals with lower extremity disabilities or spinal cord injury. Made of aluminium and stainless steel, the device enables the driver to accelerate and brake manually, and has a swivel knob for single hand steering. The control is foldable and is stored in a pouch. It can be installed in almost any vehicle by clamping the connecting rods to the corresponding pedals, strapping the clamps for safety, adjusting

Fds Transportable Left Foot Accelerator

The FDS Transportable Left Foot Accelerator is a left foot accelerator pedal designed for use by drivers with lower extremity disabilities, hemiplegic stroke, or amputation. This lightweight, compact system can installed in almost any vehicle as needed to allow the driver to use his or her left foot for braking and acceleration. The pedal is built from non corrosive materials, including aluminium, stainless steel, and marine grade plywood. The system is stowed in a special pouch. DIMENSIONS (HxL

Finger Grip Key Turner (Model 16H148)

The Finger Grip Key Turner, model 16H148, is a key holder designed for use by individuals with grasping or fine motor disabilities or arthritis. It is intended to enhance a person's ability to hold and turn a key. This key turner consists of a plastic piece with two large plastic finger loops that attaches to the base of a key with a screw so the loops extend from either side of the key. The user places his or her fingers through the loops, places the key in the lock, and rotates to lock or unlo

Fixed Ramp For Trains

The Fixed Ramp for Trains is a rail car ramp designed enable wheelchair users to enter and exit trains. The ramp set-up consists of three main elements: a Stepless Lite Ramp (see separate entry); a mechanical arm that is attached to the ramp and holds it in position; and a free-standing cabinet to store the ramp when it is not in use. When not in use, the ramp is folded width-wise and placed in the cabinet by the door. The mechanical arm allows train staff to operate the ramp and make it ready f

Flex-Ramp

The Flex-Ramp is a van ramp designed for use by individuals with mobility disabilities. This lightweight aluminum ramp converts a mini-van or full-size van into a wheelchair-accessible vehicle. The ramp is attached to the floor of the vehicle and extended outward when the door is opened. It can also be detached from the floor and moved to another location such as a curb or steps. OPTIONS: Two wheel cart for transporting ramp. SIZES: Mini-van, full-sized van, or extra capacity. DIMENSIONS (LxW):

Folding Handle For Gator Vehicle

---- CUSTOMIZED ADAPTATION --------- PURPOSE: To create a custom adapted folding handle for a John Deere Gator farm vehicle for an individual with paraplegia. An individual with paraplegia as a result of a spinal cord injury continues to work on his family’s farm and uses a Gator, an off-road vehicle, to get around the farm. The Gator allows this individual to perform tasks around the farm that would otherwise be very difficult, if not impossible, in his wheelchair. However, this individual’s t

Foldover 1:6 Low Floor Bus Ramp Er7 Series

The FOLDover 1:6 Low Floor Bus Ramp ER7 Series is a bus ramp designed for use by individuals with mobility disabilities. This electric ramp is made of stainless steel and aluminum alloy. It has a 1:16 slope and provides access to low floor buses with a floor height of 12 inches or less. A stainless steel chain and counterbalanced ramp platform allow for manual deployment or stowage. Its mechanism and controls are water resistant. An electro-magnetic latch system secures the ramp in the stowed p

Foldover Ramp (Model Fr2Ss)

The FOLDover Ramp, model FR2SS, is a bus ramp designed for use by individuals with mobility disabilities. This folding ramp can be installed for front or rear entry on a low-floor bus to provide access for passengers with wheelchairs, walkers, shopping carts, or strollers. The ramp has a non-slip surface and stows flat. Its hydraulically operated drive assembly controls platform speed through stowing and deployment. The manual back-up system requires no valve or switch movement. DIMENSIONS (LxW

Foot Control Left Foot Accelerator (Model 3545)

The Foot Control Left Foot Accelerator, model 3545S, is an accelerator pedal for persons with limited or no use of the right leg requiring them to drive with their left leg. It is equipped with a guard to prevent the driver from inadvertently resting their right foot on the accelerator pedal. The Left Foot Accelerator incorporates a quick release mechanism and is easily removable without tools.

Front And Rear Post Swing-A-Way Lifts

Fully automatic rotary lift moves platform from the van interior to the ground. The post features a gravity down operation and can be ordered for the front or rear side of the door opening. With the front post the wheelchair is loaded facing the front of the van, with the rear post the wheelchair is loaded facing the rear of the van. Hand pump for emergency backup system. Platform size: 29 3/4 inches wide by 35 inches long. Fits full size Ford and Chevy slide door or swing door vans, and full si

Full View Mirrors

Full View Mirrors are rear view mirrors designed to be installed on the windshield near the rear view mirror. They provide up to 180 degrees of rear vision, allowing the driver to see the complete rear window and most of the side windows at a glance, without the driver having to turn his or her head or body. These mirrors may also be driving/visual assistive devices for drivers with hearing impairments as they provide a means of seeing a greater area. This may allow them to see a flashing light

Fully Automatic Hydraulic Folding Lift (Models V1B1 & V1B2)

Fully automatic electric or hydraulic folding side or rear mounted van lift. Automatic safety stop. Operates from van battery. Emergency backup system included.

Fully Automatic Mini Van Lift-A-Way Lifts

Platform van lift with welded steel construction and fully automatic operation. Built in handrail. Lift models to fit most side slide doors on domestic and imported minivans and double rear doors on some domestic minivans. Box frame construction provides rigidity without relying on vehicle side wall strength. Hydraulic pump for quiet operation. Roll-stop on front of platform. Circuit breaker protects against electrical overload. Optional control box may be mounted outside the vehicle for conveni

Fully Automatic Van Lifts (L100 & L400 Series)

Platform van lift with welded steel construction and fully automatic operation. Built in handrail. Lift has models to fit most side slide, side double, and rear van and commercial vehicle doors. Box frame construction provides rigidity without relying on the vehicle side wall strength. Hydraulic pump provides quiet operation. Roll-stop on front of platform. Circuit breaker protects against electrical overload. Optional control box may be mounted outside the vehicle for convenience. Lift models p

Gas Gadget

Gas Gadget is a gas cap opener designed for use by individuals with arthritis and those with limited hand function. It is a tool designed to help minimize the effort needed to loosen and tighten auto gas caps. The Gas Gadget has an ergonomic handle that is textured and is easy to grip. The slot opening for the gas cap measures 0.5 inch wide, and 2.25 inches long. Overall the gas cap wrench measures 7 inches long. It is small enough to fit in a glove compartment, under the seat or even in some do

Gateway Ai

Gateway AI is a van lift safety lock designed for use by individuals with mobility disabilities. This product combines the Intelligent Lift Interlock System (see separate entry), which automatically prevents lift operation while the vehicle is unsecured, with the Advanced Fast Idle System (AFIS), which automatically increases engine speed when the vehicle voltage drops below 11.5 volts and the vehicle is in Park with the parking brake set. AFIS enables the vehicle's charging system to provide mo

Gear Shift Adapter (Model 107)

The Gear Shift Adapter, model 107, is an extension lever that allows the gear selector to be operated from the left hand side. The unit will not interfere with the normal operation of factory installed right handed gear selector. Mounting tools are included.

Gentleman's Pick-Up

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Pickup truck with wheelchair lift serves as less expensive alternative to a van. The user must, however, have residual ambulation ability. Describes use of a small pickup truck outfitted with a lift for an electric wheelchair. Presents advantages (i.e. cost and improved visibility) and disadvantages (possibility of rain damage, the need to be able to walk from the back of the truck to the cab), and makes suggestions concerning installation. Includes ph

Glarebuster

GlareBuster is a windshield glare screen designed for use by individuals with visual impairments who are still qualified to drive. Designed for night driving or driving in foggy, overcast, or rainy weather, this anti-glare visor reduces glare of headlights of oncoming vehicles over 70 percent, while absorbing 100 percent of hazardous blue rays and harmful ultraviolet (UV) rays, reducing eye strain and enhancing visual clarity. The lens material is extruded acrylic with a strong anti-scratch surf

Glide 'n Go Transfer Seat Bifold

The Glide æn Go Transfer Seat Bifold is a powered transfer seat designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This flip-down power lift seat raises the user from a wheelchair to vehicle seat level to enable the user to enter and exit an extended cab pickup truck. The system is operated by unfolding the safety arm and pressing the ôupö button. No structural modifications or holes are required for installation. The foldaway seat design allows

Glide 'n Go Transfer Seat Single-Fold

The Glide æn Go Transfer Seat Single-Fold is a powered transfer seat designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This power lift seat works with full- or mid-size SUVs, minivans, or short cab pickup trucks. The system is operated by unfolding the safety arm and pressing the ôupö button. No structural modifications or holes are required for installation. The lift works on either the driver or passenger side in the first or second row of sea

Grab Bar For Car.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Grab rail for car to assist walking to rear of car to retrieve wheelchair from trunk. Stainless steel rails, 3/4 inch diameter were custom made by a company that manufactures railings for boats. The rails followed the roof line of the car to be as inconspicuous as possible. The rails cost about $85 and were installed by an auto body shop. SKILLS REQUIRED: Metalworking. AUTHOR: Graichen, E. John. TITLE: Grab Bars Cheaper Than New Car. REF: Journal artic

Grip Quad Handle (Model Mp24A V)

Vertical V grip spinner for quadriplegics with some tensor control. Also call U grip spinner. Driver steers vehicle by inserting hand into V grip of spinner. Cast aluminum ball bearing base clamps to steering wheel. Grip removes easily and attaches with "Hairpin" lock. Spinner positioned at right angle to steering wheel.

Gx4 - Golf Xpress

The GX4 – Golf Xpress is an adapted golf cart or personal electric vehicle designed for use by individuals with walking, circulatory or balance disabilities or arthritis or limited stamina. This single rider golf cart enables the user to play golf without getting out of the car. When the user approaches a golf ball, he/she can position the vehicle, put it in "park," and then rotate the seat and hit the ball while seated. It has regenerative brakes with automatic parking, a full 360-degree swive

Gx4 Single Rider Golf Car

The GX4 Single Rider Golf Car is an adapted golf cart or personal electric vehicle designed for use by individuals with walking, circulatory, neurological, or balance disabilities, arthritis or limited stamina. This single rider golf cart enables the user to play golf without getting out of the cart. When the user approaches a golf ball, he or she can position the vehicle, put in it "park," and then rotate the seat and hit the ball while seated. The frame/chassis is made of welded tubular steel

Hand Brake / Clutch Control (Model 102)

The Hand Brake/Clutch Control, model 102, is a hand clutch control designed for persons without use of the left leg. This unit is similar to the Supergrade IV Hand Control (see separate entry) for operation and mounting.

Hand Clutch Control Assembly For The Ford T-25.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Clutch assembly for operators with left side paralysis who require a clutch that can be operated with the right hand. Custom modification for a Ford T 25 console. A rack and pinion arrangement with a cross shaft allows clutch to be operated from the right side of the console. The lever locks in the disengaged position and allows using the right hand for shifting gears. The lever is attached to a pivot point and linkage which connects to a cross shaft,

Hand Operated Brake And Clutch Level Assemblies For The International 1486.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Combined brake and clutch assembly for operators who require a hand operated system. The brake assembly is made of two pieces of round bar stock which were bent to follow the contour of the tractor dashboard, and clamped directly to the pedal shanks with "U"-bolts. The left hand lever is bent to the right to avoid interference with the steering wheel. The hand clutch assembly is constructed of a length of round steel bar bent 90 degrees on both ends to

Hand Operated Brake And Clutch Lever Assemblies For The International 1086 Tractor.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Combined brake and clutch assembly for operators who require a hand operated system. Extensions are constructed primarily of flat bar stock welded and bent to fit around the instrument console. Both the clutch and brake levers pivot around a shaft mounted along the front of the console. The clutch lever assembly has an added three bar linkage to allow the clutch to be disengaged and locked in place in an over-center configuration. Each brake has a shor

Hand Operated Brake And Clutch Lever Assemblies For The International 5088 Tractor.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Combined brake and clutch assembly for operators who require a hand operated system. A control jack shaft mounted under the operator's console holds all three controls. Only the left hand brake fixture is mounted permanently to the jack shaft. The clutch lever and right hand brake lever are mounted on short pieces of pipe which can rotate around the shaft. The hand levers are actuated by pushing them forward, bringing a small roller in contact with the

Hand Operated Brake Assembly For International 806.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Brake assembly designed for tractor operators who require a hand operated system. Custom modification for an International 806 tractor. The brake levels are made of flat bar stock. Each lever is attached to the brake pedal shank by two bolts. A notch has been ground at the base of the left hand control to allow the brake locking mechanism to operate freely. A handle is welded at the top of each lever and covered with a cushioned motorcycle grip. The ed

Hand Operated Brake Assembly For International Hydro 186.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Brake assembly designed for tractor operators who require a hand operated system. Custom modification for International Hydro 186 Tractor. Two vertical hand levers constructed of steel pipes are mounted in a bracket bolted to the floor. Each lever is free to rotate around a pin in the bracket. Adjustable linkage connects these levers to a second pivot assembly mounted directly beneath the left and right brake pedals. When the operator pushes the vertic

Hand Operated Brake Assembly For John Deer 3020 Tractor.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Brake assembly designed for tractor operators who require a hand operated system. Custom modification for a John Deere 3020 tractor. Two steel plates are welded to each brake shank and a portion of the pedal. The control levers are constructed of flat bar stock, which is bent to provide independent operation of each brake. Bicycle handlebar grips are welded to the bar stock to serve as handles. A steel plate is welded to each lever to serve as a base,

Hand Operated Brake Assembly For John Deer 4230 Tractor.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Brake assembly designed for tractor operators who require a hand operated system. Custom modification for a John Deer 4230 tractor. The brake levels are made of flat bar steel, bent to allow for independent use of each brake. Bicycle handlebar grips are welded to the bar steel to serve as handles. A piece of angle iron is welded to each brake pedal shank, and a piece of flat steel is welded to the end of each control lever. Each lever is bolted to an a

Hand Operated Brake Assembly For The Case 4Wd Tractor.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Brake assembly designed for tractor operators who require a hand operated system. Custom modification for a Case 4WD Tractor. Constructed of two pieces of flat bar stock welded to each side of a steel pipe hand lever. Two roller bearings are bolted to the flat steel plates. When the lever is pulled in a rearward direction the roller bearings roll up the shank to engage the brakes. The assembly is attached to a piece of channel iron bolted to the tracto

Hand Operated Brake Assembly For The International 186 Hydro.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Brake assembly designed for tractor operators who require a hand operated system. Custom modification for an International 186 Hydro. A frame designed to straddle the brake pedals made of steel plate is mounted to the tractor floor. Two hand levers run from console height down to the frame, where they are welded to a pipe which pivots around a bar supported in the frame. Two short plates or "ears" are welded to the pipe at about a 45 degree angle to th

Hand Operated Brake Assembly For The White 2-105 Tractor.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Brake assembly designed for tractor operators who require a hand operated system. Custom modification for a White 2-105 Tractor. Brake handles constructed of round bar stock are welded directly to the brake pedals. The tops are threaded to allow attachment of knobs for a comfortable grip. The editor cautions user to experiment to determine how much force is needed to operate brakes with this system. It is also noted that this design could interfere wit

Hand Operated Brake Assembly.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Brake assembly designed for tractor operators who require a hand operated system. Two levers are constructed from lengths of rectangular steel bar stock. Each bar is offset at the top to enable the user to engage each brake individually. The levers pivot around a bolt that extends through a steel bracket mounted to the tractor's instrument panel. A flat washer separates the two levers at this pivot point. Lengths of bar stock are attached by small ball

Hand Operated Brake, Clutch, And Steering Column Assemblies For Case- International 1460 Combine

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: A hand operated control system for the Case-International Combine. Hand controls were added to all the foot pedals of the Case-International Combine, allowing hand operation of the clutch, tilt steering column, and both individual brakes. The "ball" grasps were purchased from an International dealer for $10.00 each. The grasps are mounted to steel rods bent to the needed shape. The rods are bolted to the foot pedals and are removable. It is possible to

Hand Operated Brake/clutch Controls.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Conversion for disengaging clutch and engaging brake for garden tractor operators with lower extremity impairments. The clutch/brake lever is constructed from 3/4 inch steel pipe. A 90 degree elbow has been added so that the lever extends directly toward the operator. the lever fits down inside another piece of 1 inch tubing, which is secured to the pedal arm with two U-bolts. This arrangement allows the pedal to be operated in a normal manner. The edi

Hand Operated Clutch Control Assembly For The Farmall M Tractor.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Clutch assembly for operators who require a hand operated clutch. Developed for the Farmall M tractor. A 4 by 10 inch piece of steel bolts to the tractor platform through existing holes. A piece of angle iron with one side tapered to accommodate an expansion spring is welded at approximately 130 degrees on the outside angle to make the pivot point. The lever that activates the clutch is constructed of flat bar stock and is offset to avoid interference

Hand Operated Clutch Control Assembly For The International 1206.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Clutch assembly for operators who require a hand operated clutch. Modifies the clutch of an International 1206 tractor. Constructed of two pieces of flat bar stock bolted together at one end. The hand control is attached to a mounting bracket that is fastened to the side of the tractor. The hand grip is made of round bar stock bent in a "L" shape and welded to end of the hand lever. When the control is pulled backward the roller bearing pushes against

Hand Operated Clutch Control Assembly For The International 1256.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Clutch assembly for operators who require a hand operated clutch. Custom modification for an International 1256 tractor, constructed of round bar stock, flat stock, and metal tubing. The hand extension is removable to allow easier entry into the cab. Pulling back on the lever pushes the clutch pedal down and disengages the clutch. A turnbuckle in the linkage allows adjustment of pedal travel and operator reach. The editor cautions on the safety of this

Hand Operated Clutch Control Assembly For The John Deere 8430.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Clutch assembly for operators who require a hand operated clutch. Custom modification for a John Deere 8430 tractor. A lever constructed of 1 and 1/4 inch by 1/4 inch flat steel is attached to a fixed point on the side of the steering console. As the lever is pulled toward the operator, a roller bearing mounted on the end of the lever rolls along the lower shank of the clutch pedal, disengaging the clutch. The roller is used to reduce the effort requir

Hand Operated Clutch Control For The Farmall H.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Clutch assembly for operators who require a hand operated clutch. Custom modification for a Farmall H is operated from the left side of the tractor. The handle is a locking lever connected to the existing clutch pedal. It is mounted to the shank of the clutch pedal by bolts. A guide arm is bolted to the side of the tractor and platform. The guide is constructed of 1/2 inch bar stock and notched to allow the clutch to be locked in the disengaged positio

Hand Splint Designed To Eliminate The Need To Grip.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: To eliminate need for gripping during operation of skid loader by persons with hand impairments. The hand portion of the splint was heated and molded around a short section of 1 inch black PVC pipe which rests in the palm of the hand. The splint is held to the wrist by velcro straps. To operate a lever, the user places the pipe over it and then pushes or pulls without gripping. SKILLS REQUIRED:Moldmaking. Plastics. AUTHOR: Field, W.E. TITLE:Agricultura

Handicap Placard Clip

The Handicap Placard Clip is a disabled parking permit holder designed for use by individuals with balance, mobility, neurological, or circulatory disabilities. This holder clips securely to both the rear view mirror and the placard. It has a double-swivel mechanism that enables the sign fixed in two positions. When the car is parked, the placard is set to hang under the mirror in plain view. When driving, the sign can be flipped up, out of the driver's line of sight. DIMENSIONS(LxW): 4.5 x 3.25

Handicap Placard Protector

The Handicap Placard Protector is a disabled parking permit holder designed for use by individuals with mobility, neurological, or circulatory disabilities. This protector keeps parking permits visible while protecting them from damage and wear. The clear plastic sleeve slips over placards and hangs from vehicle rear view mirror with the built-in hook. DIMENSIONS(LxW): 11.5 x 4.75 inches.

Handiramp Van Ramp System Series

The HandiRamp Van Ramp System Series are van ramps designed for use to provide access to vans and mini-vans. The system is mounted with a 3-bolt installation. Ramps are made from either aluminum or expanded metal with non-skid tread ways and wheel guides. All ramps in the series are equipped with spring assisted lifting, and fold up vertically inside the van door to conserve passenger space. OPTIONS: Floor mount; step well mount. DIMENSIONS: 5, 6.5, 7, or 8 feet long. Aluminum ramps are not avai

Handle For Key Ring.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Easy to hold handle to attach to a key ring. Key ring handle made of strips of metal riveted together in a T shape with a loop in the bottom to fit around the ring. SKILLS REQUIRED: Metalworking. AUTHOR: Independence Factory TITLE: Make it Cheap: Volume 3 REF: Middletown, Ohio: Independence Factory NARIC CALL NUMBER: R1183 PAGES (including cover): 2 1976.

Handy Bar

The Handy Bar is an tool designed to offer more support as individuals get out of the car. Good for users with stability or balance issues. To use, insert the handle into the u-shaped door striker on the vehicle door frame. The Handy Bar easily locks into place and can be used on both the driver and passenger's side. Also features a seat belt cutter and window breaker for emergencies. Stores in the glove compartment and fits most cars in the U.S.

Handybar Automobility Solution Kit With Swivel Cushion

The Handybar Automobility Solution Kit with Swivel Cushion is designed to assist individuals with limited mobility while getting in and out of low-to-the-ground vehicles, SUV's and trucks. This kit includes both the Handybar 3-in-1 Car Aid and Swivel Cushion, which assist in transferring from a car-entry position to car-sitting position in one fluid motion without difficult maneuvers or painful twisting. The Swivel Cushion works well to reduce pain on the back, hips and knees. Ideal for car seat

Hercules (Models 2000 & 3000)

Hercules, model 2000 and 3000 is a trunk mounted scooter loader or van lift designed to lift scooters into vans or car trunks. These lifts feature an aluminized bronze sprocket that is non-corrosive and stronger than most steel. The sprocket assembly creates a four-to-one gear ratio for increased lifting capacity and the assembly is supported by a haf-inch steel shaft and needle bearing. The gearbox location allows greater height clearance and a low center of gravity provides ease in handling. T

Hitch Mounted Ramp

The Mounted Ramp is designed for use by individuals who use powered wheelchairs or scooters. This ramp enables users to load a power chair or scooter into the back of vehicles equipped with a rear hatch or barn-style doors, such as SUVs (sport utility vehicles)and minivans. The universal design is compatible with all lift-gate equipped vehicles and connects to a Class I, II or III trailer hitch with no drilling. This ramp requires only 15 pounds of force to operate. The non-skid metal surface is

Hole-In-One Key Holder (Models F75412-1000)

The Hole-In-One Key Holder, model F75412-1000, is a key holder designed for individuals with arthritis or limited hand mobility/strength. This key holder provides a rigid handle for extra leverage when turning keys, as well as several grasping positions: Users can either slide their fingers through the hole in the center of the handle or grasp the entire handle. Chrome-plated screws hold up to two keys, and the keys can be folded back into the inner curved side of the plastic holder when not in

Homemade Van Ramp.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Wheelchair ramp for a van. Describes a wheelchair ramp made of strong 1/4 inch aluminum channel irons and angle cross pieces from a boat manufacturing plant. The runners are made of two 45 inch sections each, hinged together with barn door hinges. Shallow steps are built between the runners, and covered with indoor-outdoor carpeting. Includes photographs. COMMENTS: Developed by Harley Karvonen of Perham, Minnesota. SKILLS REQUIRED: Metalworking. Woodwo

Horizontal Steering

The Horizontal System is a horizontal steering column manufacturer recommended for drivers with limited reach and strength capabilities. The system utilizes a level-planed steering wheel as opposed to the conventional vertical-planed steering wheel that is extended over the driver's lap.

Hosmer Driving Ring

The Hosmer Driving Ring is a steering wheel spinner ring for upper extremity amputees that is designed for use on automobile steering wheels, boat tillers, aircraft controls, and most bicycles. The device attaches with a clamp to the steering instrument; the side of the clamp has a rubber surface for a secure grip. The swivel ring is coated in plastic, and has a 4/5-inch inside diameter.

Hydraulic Hand Operated Brake And Clutch Control For A John Deer 350 Bulldozer.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: To provide access to a John Deere 350 Bulldozer for operators requiring a system of hand operation. Conversion taps into the bulldozer's existing hydraulic system and is set up to disengage the master clutch, apply the brakes of both the tracks at once, and assist the left and right hand steering levers. Two new valves are added above the instrument console directly in front of the operators seat. Through hydraulics, one finger is sufficient to operate

Intelligent Lift Interlock System (Ilis)

The Intelligent Lift Interlock System (ILIS) is a van lift saftey lock designed for use by individuals with mobility disabilities. This solid-state, microprocessor-controlled unit automatically prevents lift operation while the vehicle is unsecured and prevents driving the vehicle with the parking brake left on. A dash-mounted LED panel displays system and sub-system status. An Intermittent Fault Filter (IFF) filters out erroneous changes in sensor signals, and the system performs self-diagnosti

Kar Kady

Wheelchair carrier attaches to standard trailer hitch (not included). Spring assist raises chair into storage position. Weight 13 pounds. Dimensions: 32.5 by 18 by 7.5 inches. Aluminum and stainless steel construction. Chair cover available ($65.95).

Key Holder "dumbbell" (Model Sw5180)

The Key Holder "Dumbbell," model SW5180, is a key holder designed for use by individuals with arthritis and other grasping disabilities. The device consists of a chrome-plated steel rod with a plastic ball screwed on either end. The rod holds up to 10 keys and provides leverage for turning keys, including ignition keys for automobiles. DIMENSIONS: 3.5 x 0.5 inches.

Key Lever (Model 3205)

The Key Lever, model 3205, is a key holder designed for use by people who have difficulty grasping or turning keys. The cylindrical device holds and positions up to three keys and once the key is inserted in the lock, the device assists with turning. A hole in one end accepts a pencil for grasping and leverage. DIMENSIONS: Each side is 1.5 inches long and .5-inch in diameter.

Key Lever (Model Dl1905)

The Key Lever, model DL1905, is a key holder designed for use by individuals with grasping or fine motor disabilities. This key accessory provides leverage for any key, including car keys with thicker fobs. The key slips over a screw bar in the center, then the bar is screwed back together. To add or remove the key, there are holes in each side of the lever. Pencils can be slipped through these holes to aid in turning the lever. DIMENSIONS: Bar is 3 inches long and 0.5 inches thick.

Key Ring

The Key Ring is designed especially for wheelchair users. It attaches to the arm rest of a wheelchiar. The key ring is made with a heavy duty split ring-snap fasteners and leather.

Key Turner Iii (Model Nc28255)

The Key Turner III, model NC28255, is a key holder designed to assist persons with limited wrist strength or movement. The Key Turner III features a heavy-duty plastic handle that provides extra leverage for turning. Keys fold into the handle when not in use. The Key Turner III holds three standard keys. DIMENSIONS (LxW): 4.75 x 0.88 inches. The circumference is 4.13 inches.

Kidster Chair

The Kidster chair is an individual wheelchair seating system designed for children from 2 to 12 years, or any individuals who fit into the seat sizes offered. The seat is certified as a child safety car seat when removed from the frame, and is designed for use as a positioner, self-mobile unit, recliner, floor sitter, and stroller. FRAME: The frame is made of steel and is coated with baked on nylon. The frame comes in black, blue or red. SEAT: A rigid seat with 2 inches of regular polyurethane s

Kliktronic Electronic Shifter

The Kliktronic Electronic Shifter is a motorcycle or automobile hand control designed for use by individuals with physical disabilities. This push button gearchange system is suitable for all bikes and bike-engined cars, offering an alternative to manual shifting. Each kit includes a switch, actuator assembly, electronic control box, and mounting clamp. Bike kits are available with switches designed for underbar or onbar mounting. The car kit includes a switch designed for mounting on the steeri

Kneelvan

Kneelvan is a mini van with ramp designed for use by individuals with mobility disabilities or spinal cord injury. This van is a conversion of the Dodge Grand Caravan, Ford Windstar, or Chrysler Town & Country minivan, featuring a rear opening ramp and standard hydraulic kneel-down. Available interior configurations include: two bucket seats in the middle row on either side of the wheelchair, with a two-person fold-down bench that folds up when not needed in the back row; remounting the orig

Knob Steering Device (Model 101K)

The Knob Steering Device, model 101K, is a steering wheel spinner designed for use by individuals who use driving hand controls or who have upper extremity disabilities. This raised knob attaches to one side of the steering wheel to facilitate one-handed steering.

Laundry Trolly

The Laundry trolley is designed for individuals who are unable to bend down to pick up their laundry basket or who need a laundry basket with wheels in order to carry it to the washing machine.

Lectra Aid Person Van Lift

Platform van lift. Dropped swing arm bracket with chair attaches with bolts to door post. Aluminum. Weight approximately 38 pounds. Operates off 12 volt vehicle battery. Seat dimensions 18 by 18 inches. Seat has non-slip neoprene cover. Custom lifts available.

Lectra Liftami

Electric lift for wheelchair alternatives. Bolts onto class 3 trailer hitch. Weight 62 pounds. Platform base folds up against rear of vehicle when not in use. Drive-on platforms available for 3 or 4 wheel scooters. Liftami II folds down to allow access to trunk or van doors. Includes night lift lights, high center-mounted brake light. Also available: nylon cover ($38.50); Inside trunk lift ($795.00).

Left Accelerator Pedal (Model La-2)

The Left Accelerator Pedal, model LA-2, is an adapted driving control unit designed to enable drivers without the use of their right foot to drive standard vehicles. The unit has a spring-loaded pedal to reduce fatigue and a right foot stopper plate for added safety. The unit is mounted on the floor of the car and can be removed with a one-hand quick-release operation.

Left Foot Gas (Model 104)

The Left Foot Gas, model 104, is an accelerator pedal for the left foot designed to be mounted on the left side of the brake pedal for drivers with limited or no use of their right foot. The device includes a floor mount plate that requires four screws. The plate remains on floor, enabling the pedal to be removed and reinstalled with an allen keyas needed.

Left Foot Gas Pedal

The Left Foot Gas Pedal enables drivers with limited or no use of their right leg to drive car with left leg. The right pedal is actuated through roller riding on factory pedal. The unit can slide over and fold to floor when not in use.

Liberator Plus Trunk Lift (Model Flc-2000-Hdab)

The Liberator Plus Trunk Lift, model FLC-2000-HDAB, is a trunk mounted scooter or power wheelchair loader designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This heavy duty lift is constructed of welded steel with a powder coated finish, and comes with an adjustable reinforced deck base that bolts to the trunk or cargo area floor in a car, van, or SUV. It has a motorized lifting strap with a manual boom swing and hand held push button controls, a

Liberator Trunk Lift (Models Flc-0200-Ef & Flc-0200-Es)

The Liberator Trunk Lift is a trunk mounted scooter or power wheelchair loader designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. Model FLC-0200-ES is stowable and model FLC-0200-EF is foldable. The lift is constructed of welded steel with a powder-coated finish, and comes with a deck base that bolts to the trunk or cargo area floor in a car, van, or SUV. It has a motorized lifting strap with a manual boom swing and hand held push button controls

Liberator With Hitch Mount Receiver Base (Models Flc-0200-Sr-2 & Flc-0200-Sr-3)

The Liberator With Hitch Mount Receiver Base is a hitch mounted scooter or power wheelchair loader designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. Model FLC-0200-SR-2 mounts to a Class II (1.25-inch) hitch receiver and model FLC-0200-SR-3 mounts to a Class III (2-inch) hitch receiver on a car, van, or SUV. Both are stowable. The lift is constructed of welded steel with a powder-coated finish, and comes with a motorized lifting strap, a manual

Lift'n'go (Model 210)

The Lift'N'Go, model 210, is a hitch-mounted wheelchair carrier designed for use by individuals with mobility disabilities or spinal cord injury. This electrically-powered universal carrier can be used to transport scooters and wheelchairs, including heavy scooters and mid-wheel drive chairs. It has a carrying platform with five tie-down locations and three nylon straps to secure the chair or scooter during transport. There is a backup hand crank with a stroke lift of 22 inches. The carrier requ

Lift-All

The Lift-All is an electric, trunk-mounted wheelchair loader with a built-in control. The lift is designed to be permanently installed in one side of a car's trunk or in a van, RV or truck. The lift's arm folds flat in the trunk, unfolds and locks in the operating position. The lift's boom swivels more than 90 degrees. The unit lifts the base of an Amigo with the seat and T-handle removed, but must be manually positioned over the trunk before lowering the scooter into the car's trunk. The lift c

Liftami Iii

Lift arm loads scooters into automobile trunks, vans, station wagons and hatchbacks. Vehicle installation involves bolting heavy duty base plate inside vehicle, and adjusting boom length and height to individual needs. The unit can be wired directly to auto battery or to scooter battery. Lifting is accomplished by an electric 12 volt screw actuator. Optional "C-Bar" lift arm allows scooters to be loaded without disassembly into mini vans, sport trucks or pickups. By removing seat and tiller, sco

Liftami Iv

Platform lift for electric wheelchairs up to 225 pounds. Also accommodates four wheel scooters. This unit bolts onto a class III receiver hitch and can be mounted to the rear of automobile by a local trailer hitch installer. A twelve volt motor raises and lowers the platform which can be folded and locked in vertical position when not in use. The platform is all aluminum and features "liftlites" for night use and a D.O.T. approved center breaklight.

Literamp Portable 1-Piece Wheelchair Ramp

The LiteRamp Portable 1-Piece Wheelchair Ramp is a portable ramp designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury or others who use a wheelchair or scooter. The ramp has carrying handles, folds in the middle, and can be carried like a suitcase. It is made from aircraft aluminum, and it is fully covered with safety non-skid tape. This ramp is weather resistant so it can be left outdoor year-round. It is self-supporting to prevent slippage on sta

Literamp Portable 2-Piece Wheelchair Ramp

The LiteRamp Portable 2-Piece Wheelchair Ramp is a portable ramp designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. The ramp can be taken apart into two separate pieces side by side. Each piece folds length-wise and has two handles so it can be carried like a suitcase. The ramp can accommodate 3-wheel scooters as well as manual or electric wheelchairs. It can be used on curbs, decks, and steps; on side doors of vans; on back doors of most vans an

Load 'n Go Power Hatch Assist

The Load 'N Go Power Hatch Assist is a power car door opener and closer designed for use by individuals with physical disabilities. This unit automatically opens and closes rear hatch doors. It mounts to existing door hardware and comes with a hidden magnetic switch and latch release. It can be used on selected vehicles from Daimler Chrysler/Dodge, General Motors, Ford/Lincoln, as well as the Honda Odyssey, Kia Sedona, Mazda MPV, Nissan Quest, Toyota Sienna, and Volkswagen Eurovan. The unit come

Load 'n Go Power Wheelchair / Scooter Lift

The Load 'N Go Power Wheelchair/Scooter Lift is a truk mounted scooter or power wheelchair loader designed for use by individuals with mobility disabilities. This loader is designed for use in vehicles with hatchbacks. All lift functions are controlled by the touch of a button on a handheld pendant. The lift allows extended clearance between the vehicle and the scooter or wheelchair. A power swivel option guides the scooter or wheelchair into the vehicle.

Lp11 Mobile Lifting Platform

The LP11 Mobile Lifting Platform is an interior or exterior wheelchair lift and wheelchair lift for rail cars designed to aid people in wheelchairs to enter and exit structures with doorways above ground level or trains with doorways that are above the level of the train station platform. The lift has railings on both sides and ramps on both the front and back ends that can drop down past horizontal and raise into a vertical position. It has a base with four wheels so it can be moved into positi

Lp12 Lifting Platform

The LP12 Lifting Platform is an interior or exterior wheelchair lift and wheelchair lift for rail cars designed to aid people in wheelchairs to enter and exit raised platforms or stages, structures with doorways above ground level, or trains with doorways that are above the level of the train station platform. The LP12 has a wheeled base, and it is moved into position before use with a control arm that extends from one side of the base. There is a central wheel lock to fix the unit’s position. T

Manual Bi-Fold Van Ramp (Models Mf-26, Mf-30 & Mf-36)

The Manual Bi-Fold Van Ramp, models MF-26, MF-30 and MF-36, is a van ramp designed for use by individuals with mobility disabilities or spinal cord injury. Constructed from 6061 Aerospace-grade aluminum, the ramp installs in a van to provide wheelchair access. The ramp is also available as a twin track pair. DIMENSIONS (LxW): 72 x 26 inches (MF-26) 96 x 30 inches (MF-30), or 96 x 36 inches (MF-36). Twin tracks are 12 inches wide.

Max Ii And Max Iv

All terrain vehicle. Polyethylene body. 5 or 6 gallon fuel tank. Hand controls. Steering levers with throttle mounted on handle. Levers control direction of vehicle as well as braking. Gear shift lever under seat. 2 or 4 cycle gas engine. 2 or 4 passenger models. 6 driving wheels. Max II: 86 inches long by 37 inches high by 56 inches wide, 2 seater weight 1,100 to 1,210 pounds. Max IV: 96 inches long by 42 inches high by 56 inches wide, 4 seater, weight 1,775 pounds. Optional accessories: roll b

Mercury Airchair

The Mercury AirChair is an emergency evacuation carrier and transfer wheelchair for onboard an airplane designed for use by individuals with lower extremity, mobility, or neurological disabilities, or spinal cord injury. FRAME: Made of high strength aluminum alloy, this folding frame is available in three widths - 14, 15 and 16 inches. Overall height is 34.1 inches for all width. Folded dimensions (HxWxD): 28.3 x 14.7 x 7.5 inches (14-inch width); 28.3 x 15.7 x 7.5 inches (15-inch width); 28.3 x

Micro Buggy

PROTOTYPE--- The Micro Buggy is an off-road wheelchair designed for use by individuals with lower extremity or mobility disabilities. This gas powered wheelchair can be used for recreation or for tasks such as walking the dog. FRAME: Adjustable suspension; automatic transmission; 3 forward gears and 1 reverse gear; 1.5 inch receiver hitch in front and rear; 8 inch suspension travel; expandable storage system that slip links storage baskets. CONTROLS: The unit is all hand controlled, with a thumb

Micro Inside Lift (Model Al055)

The Micro Inside Lift, model AL055, is a van lift without platform designed for use by individuals with mobility disabilities or spinal cord injury. This powered lift uses a boom with manual rotation to lift the lightweight wheelchair or travel scooter and can be used with vans, SUVs or the trunk of most cars. Docking devices are available to accommodate smaller scooters and chairs. The boom has a range of 360 degrees. DIMENSIONS: The lift requires 37 inches of headroom, but may be modified for

Micro Scooter Lift (Model Al010)

The Micro Scooter Lift, model AL010, is a hitch-mounted scooter carrier designed for use by individuals with mobility disabilities or spinal cord injury. This carrier is designed for lightweight micro or travel type three-wheel scooters. This compact carrier with a motorized lift can be mounted on a Class I, II, or III trailer hitch. The carrier folds manuallly and has a "hold down foot" feature for securing the scooter. POWER: Uses a battery and a supplied electrical harness with full-length le

Microsoft Eye Gaze

---- PROTOTYPE --------- PURPOSE: To create a prototype of a gaze-controlled interface cursor to assist those with fine motor and/or hand disabilities. Those with disabilities such as Amyotrophic lateral sclerosis (ALS), have a hard time controlling their limbs and communicating, making it hard to utilize communication tools, electronic devices, or simply be independent. The Eye Gaze device functions on eyesight--a user can roll their eyes over a virtual keyboard to communicate with others. The

Millennium Series Lift

The Millennium Series Lift is a platform van lift designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This fully hydraulic lift is designed for installation in the side or rear door of a full-size van. It has a hand-held control and on-lift controls mounted on an arm that extends from the lift frame; a remote control is optional. The Millennium Series also features a manual backup system; an outboard roll top that engages in the fully up position

Mini-Touch Vehicle Control Pad

The Mini-Touch Vehicle Control Pad is a hand-operated driving control system designed for use by individuals with lower extremity disabilities or spinal cord injury. This steering wheel mounted control pad enables hand control of vehicle functions such as wipers, turn signals, horn, and high/low beams. The standard unit has 6 functions. Original controls remain fully functional. The control is transferable to most makes and models of vehicle, and can be configured for foot-control use. OPTIONS:

Mirage Transit

Mirage Transit is a bus lift designed for use by individuals with mobility disabilities. Constructed of steel and aluminum, this underfloor lift stows away in an enclosure beneath the vehicle floor when not in use, leaving the doorway clear. The enclosure also protects the lift from rain, snow, and dirt. The lift raises, lowers, stows and deploys at the touch of a button, using hydraulic power provided by a remotely located hydraulic Power Pak. Manual backup is standard. POWER: Hydraulic Power P

Mobile-Lift Inside

The Mobile-Lift Inside, model 19680, is a wheelchair alternative lift for vans. The unit is installed inside a van, trunk, or station wagon and swings out and lowers the scooter. A claw hook and t-bar docking device allows fast loading with safe weight-balanced operation. The entire unit swivels on a roller-bearing surface. It comes with a quick disconnect plug set, as well as mounting hardware and installation instructions. Full-size scooters do not need to be disassembled for loading into

Mobile-Lift Outside

The Mobile-Lift Outside model is a bumper-mounted wheelchair alternative carrier designed to allow scooter users to drive onto the platform, get off, and push a switch to lift. The lift raises and locks any scooter into place on the back of a car in about 60 seconds. The unit folds up out of the way when not in use. A quiet, electric motor lowers the platform. The scooter is attached with adjustable safety belts. Two models are available. Model 19500 is designed for 3-wheel scooters and is t

Mobile-Lift Rv

The Mobile-Lift RV model is a hitch-mounted powered wheelchair alternative carrier designed for use on recreational vehicles. The lift raises and locks any scooter into place at the rear of the vehicle. The scooter does not need to be disassembled for loading. This powered lifter has an aluminum platform, two night lights for evening use, and a Department of Transportation-approved center brake light. The rectangular platform that folds up vertically when not in use. The lift is installed us

Mobilift Aircraft Wheelchair Lift (Models Ax & Axr)

The Mobilift Aircraft Wheelchair Lift is a wheelchair lift for aircraft boarding designed for use by individuals with mobility disabilities or spinal cord injury. This crank-operated unit can be used to enplane and deplane passengers with disabilities on regional and narrow body aircraft that are ground loading, including 737, 727, DC9, MD80, and F28 planes. The lift deck is supported at all four corners, and is designed to hold standard aircraft boarding chairs. DIMENSIONS (HxLxW): Model AX is

Mobilift Tx Wheelchair Lift For Trains

The Mobilift TX Wheelchair Lift for Trains is a portable wheelchair and scooter lift designed for use by individuals with mobility disabilities or spinal cord injury. This manual lift has a cranking system that allows a 300-pound passenger to be lifted with 11 pounds of crank force. The unit has large wheels to help negotiate rough terrain, and can be loaded onto any size pickup truck for multi-destination use. The lift can be moved on a hard level surface with four pounds of pressure. The lift

Mobilityworks Ultra Wheelchair Van

The MobilityWorks Ultra Wheelchair Van is a van conversion designed for use by indviduals with mobility disabilities or spinal cord injury. The conversion is a full-sized lowered floor van built on the Ford E150-Series or E-250 Series chassis. Standard features include two front captain chairs, manual bi-fold sofa with drink holders and three-point safety restraints, deep-tint vista windows, polyurethane foam floor with high-traffic cobblestone carpet, high output rear air conditioning and heat,

Mobilityworks Wheelchair Vans & Ambulettes

MobilityWorks Wheelchair Vans and Ambulettes are public transport vans designed for use by individuals with mobility disabilities or spinal cord injury. Ambulettes are non-emergency wheelchair vans which are typically used by nursing homes, adult day care centers, hospitals, transport companies, medical transportation providers, EMS facilities, fire departments, and facilities for individuals with intellectual or developmental disabilities. Vehicles feature one-piece plastic walls for ease of cl

Monarch Mark Ia

The Monarch Mark IA is a hand control made of steel, stainless steel, and aluminum. The device is operated by pushing a handle parallel to the steering column for brake and at right angle towards the driver's lap for acceleration. The control also has toggle switches for light dimmer and horn. The hand control will not interfere with operation of the vehicle by an able-bodied driver. The control can be positioned for left or right hand operation. INSTALLATION: The device has a V-block mount and

Motomate (Models 6060 & 6260)

The Motomate are driving hand controls designed for use by individuals with lower extremity disabilities or spinal cord injury and those with the use of only one hand. Designed to respond to driver commands, the user pushes forward to brake and downward to accelerate. Both of these actions are intended to correspond to the driver’s natural motions. This product features a padded grip and can be mounted to either the right or left side of the steering wheel to suit the user’s need. Model 6260 is

Motorhome Lift (Model 124)

The Motorhome Lift, model 124, is a mobile homelift designed for use by individuals with mobility disabilities or spinal cord injury. This steel lift is designed without a platform and operated by suspending the wheelchair and the user from a vertically pivoting arm. The arm pivots down to attach to the occupied wheelchair, then lifts the occupant and chair into the motorhome. Permanently attached nylon webbing attach chair to the arm of the lift (permanent, detachable or temporary visitor hooku

Mps Quick Release Left Foot Gas Pedal With Pedal Guard

The MPS Quick Release Left Foot Gas Pedal with Pedal Guard is an accelerator pedal for persons with limited or no use of the right leg requiring them to drive with their left leg. This pedal is installed on the left side and is mechanically linked to the original manufacturers pedal. The Pedal Guard shields the original pedal to make it inoperable. The pedal is fully adjustable. The lightweight design of the pedal and its quick release feature facilitate easy removal.

Multi-Lift

The Multi-Lift is a powered sling transfer lift designed for use by individuals with mobility disabilities. This portable lift can be used to transfer the user into or out of a car or other vehicle, or to or from a bed, sofa, toilet, or bath. It can also be used to lift a scooter or power wheelchair into a station wagon or minivan. It comes powder coat painted finish is standard and a wide variety of slings is offered. POWER: Uses 12v/25A Surge, 20A Continuous. OPTIONS: Home wall mount, home f

Multifold Ramp (Models Wcr530, Wcr630, Wcr730, Wcr830, Wcr1030, & Wcr1230)

The Multifold Ramp is a portable ramp designed to provide wheelchair or scooter access over steps and curbs or into full-sized vans and minivans. This aluminum ramp is hinged to fold in several places for transport. Ramps feature auto-locking and a suitcase-style carrying handle. The ramp is surfaced with anti-slip, high-traction safety tape. DIMENSIONS: Unfolded ramps are 30 inches wide and 5 feet (WCR530), 6 feet (WCR630), 7 feet (WCR730), 8 feet (WCR830), 10 feet (WCR1030), or 12 feet (WCR123

Mv-1

The MV-1 is a minivan with ramp designed for use by individuals who use wheelchairs. Designed from the ground up for wheelchair accessibility, this vehicle was engineered according to the principles of Universal Design, which allow for the ease of accessibility regardless of any mobility issues. It provides for the accessibility of most wheelchairs and scooters, while providing a comfortable and safe ride for all. This vehicle is equipped with an integrated deployable ramp with a shallow ramp an

No Glare Visor Extender

The No Glare Visor Extender is a windshield glare screen extender designed for use by visual impairments who are still qualified to drive. Designed to block blinding glare from sunlight, this device clips onto a car's existing visor to reduce eye strain for safer driving. It is made of optically-clear green plastic and flips up and out of the way when not in use. DIMENSIONS (LxW): 11.25 x 4.25 inches. The distance between clips is 6 inches.

No Start Car Disconnect Switch

The No Start Car Disconnect Switch is an ignition disconnect switch designed for use with individuals with Alzheimer's disease, dementia, or cognitive disabilities. This unit prevents an automobile from being started by someone who does not understand that driving is dangerous for them. This device connects to the battery and enable the car to be disabled with the turn of a knob.

Noggie‚Ñ¢ Plush

Noggie™ Plush is a support soft seat designed for use by premature infants weighing up to 8 pounds while positioned in a car seat or stroller. It has two firm arms that wrap around the infant to provide comfort and support. The flexible arms move up or down, to the front or sides to meet individual needs. The removable head supports and cradles the infants head and neck and can be adjusted up or down to accommodate the infants growing needs. The Noggie™ Plush slips easily into infant carrie

Omnigo Wheelchair Lift

The Omnigo Wheelchair Lift is a car top mounted wheelchair carrier for manual wheelchairs. The device is designed for less than a minute operation. A hand-controlled switch lowers the lift arm; the folded wheelchair wheels onto the loading arm; a second flip of the switch makes the chair automatically ascend to the top of the car and a cover lowers over the chair. The carrier mounts to the car top like a standard roof rack and causes minimum wind resistance. The device is made of aluminum and st

One-Hand Driving Device

-- PROTOTYPE --------- PURPOSE: To create a prototype of a device that allows drivers with disabilities steer, accelerate, change gears and brake with one hand. Users with reduced hand strength can easily use this device since it is completely electronically controlled—no mechanics are involved. To simulate the natural haptic feedback provided by a mechanical steering wheel, motors have been added to the device to simulate those sensations. The ease in which the device is operated can also be ad

Orion Low Floor Minibus

The Orion Low Floor Minibus is a low floor public transport van designed for use individuals with lower extremity, mobility or walking disabilities or spinal cord injury and others who use wheelchairs. This kneeling minibus has a full length flat floor and is available with a wide range of seating and internal layouts. Passengers can enter or exit via ramp or a single step. It has seating for up to 18 passengers, plus driver, with up to 16 passenger seats and space for up to 5 full sized wheelc

Out-Rider Vehicle Lift (Model Pul-1100)

The Out-Rider Vehicle Lift, model PUL-1100, is a wheelchair loader for pickup trucks designed to lift and store fully assembled scooters and manual wheelchairs behind the driver's cab of a full-size, mid-size, or king cab pick-up truck. The wheelchair lift can be mounted on the truck just behind the cab on either the driver's side or the passenger's side. A "docking device" is attached to the wheelchair; different devices are used for standard wheelchairs and for wheelchair alternatives. For sta

Pac All Bumper Deck

Platform mounts to the rear bumper of a car. Heavy duty aluminum frame. Provides access to trunk while the carrier is mounted. 28 inches wide by 23 inches deep. Rear supports are 28 inches high. Holds up to 150 pounds. Can be used to transport luggage, bikes, etc.

Pac All Dual Carrier

Bumper mounted carrier for standard wheelchair or scooter powered wheelchair. Fits on standard front or rear bumpers without a hitch (hitch adapter available). Support tubes are inserted into sockets and loack in place. Wheelchair or scooter must be lifted manually to knee height. Heavy duty rust proof aluminum. Includes all hardware and installation instructions.

Pac All Wheelchair Carrier

Wheelchair carrier installs on front or rear bumper of most automobiles, vans or recreational vehicles (RVs). Brackets attach to bumper and are the only visible component when the carrier is not in use. Support tubes insert in sockets and lock in place; wheelchair is tilted back and then forward to rest the rear wheel on its bracket. Tie down (included) secure the chair. Heavy duty rust proof aluminum.

Pac-All Scooter Carrier

Bumper mounted scooter carrier. Aluminum. Nylon straps. 150 pound maximum weight capacity. Fits on standard bumpers without hitch. Hitch adapter available. Scooter must be manually lifted to knee height. Cover available.

Pacer

The Pacer is a public transport van designed to provide transit for wheelchair users and able-bodied individuals. The vehicle has fully laminated steel reinforced cage construction to enhance passenger safety and features maximum headroom (76.5 inches), a wide aisle, and large seats. The Pacer is available in a wide variety of floorplans (to accommodate from 13 able-bodied individuals to 6 able-bodied individuals and 3 wheelchair users) with a number of features and options to fit specific needs

Padded Swivel Cushion With Carry Strap (Model 14A063-1)

The Padded Swivel Cushion With Carry Strap, model 77142, is a swivel cushion designed for use by individuals with back pain and mobility disabilities. This transfer cushion takes pressure and strain off the back and hips while turning when driving an automobile. It consists of a soft, lightweight foam-padded seat with a velour cover and comes with a carrying strap. The seat rotates at 360 degrees. CAPACITY: 300 pounds. DIMENSIONS: 1 inch thick. COLOR: Velour cover is gray.

Palm Grip Quad Handle (Model Mp23A)

Grip Quad Handle for quadriplegic resembles has closed loop handle that fits around fingers and hand. Used by persons with average tensor control who find flat hand position comfortable for driving. User steers vehicle by sliding hand and fingers through top of spinner. Base is cast aluminum ball bearing and clamps securely to steering wheel. Spinner positioned at right angle to steering wheel.

Palm Spinner

The Palm Spinner is a steering wheel spinner designed for use by individuals with grasping or upper extremity disabilities or spinal cord injury. This device attaches to the steering wheel and has two adjustable pieces that hold the driver's hand in place on the rim of the wheel. The spinner can be removed when not required by the driver. WARRANTY: 5 years.

Panamirror Clip-On Driving Mirror (Model 70330)

The Panamirror is a clip-on rear view mirror designed to ensure driving safety for individuals who are deaf or hard of hearing. It is a precision, optically designed mirror that provides a clear view as wide as the rear window of the car, increasing the peripheral viewing area and cutting down on glare. The mirror is designed to fit easily over an existing rear view mirror. DIMENSIONS: 10 x 2.25 inches.

Panoramic Rearview Mirror (Model D706)

The Panoramic Rearview Mirror, model D706, is an enlarged rear view mirror designed for persons with cervical arthritis or other conditions which would preclude extended turning of the neck and head. The unit clips over the existing mirror. It is made of shatterproof, no glare materials.

Para-Transit

The Para-Transit is a public transport van designed to provide transit for wheelchair users and able-bodied individuals. The vehicle has a unitized steel roll-cage construction to enhance passenger safety and features maximum headroom (76.5 inches), a wide aisle, and large seats. The Para-Transit is available in a wide variety of floorplans (to accommodate from 20 able-bodied individuals and 1 wheelchair user to 12 able-bodied individuals and 4 wheelchair users) with a number of features and opt

Park Brake Extension (Model 105)

The Park Brake Extension, model 105, is an extension lever that bolts to a foot operated parking brake in order to operate the brake by hand. The lever can be installed at various angles by adjusting the position in relation to the attachment bolt.

Parking Brake Extension

The Parking Brake Extension is a parking brake extension lever designed for use by individuals with lower extremity disabilities or spinal cord injury. This device attaches to the parking brake and enables the brake to be operated by hand. WARRANTY: 5 years.

Passenger Position Wheelchair Lock

The Passenger Position Wheelchair Lock is a wheelchair restraint system to secure a wheelchair in moving vehicle. It is attached by an attendant who locks the chair to tracks in the floor with four ratchet-tightened straps. Seat shoulder belts required.

Patriot Power Chair Lift (Models Flc-0500-2 & Flc-0500-3)

The Patriot Power Chair Lift is a hitch mounted wheelchair lift designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. The lift mounts on a Class II (model FLC-0500-2) or Class III (model FLC-0500-3) receiver hitch, and carries power chairs with a maximum width of 27 inches and a maximum wheelbase of 35 inches. POWER: Uses 12-volt direct current motor powered by the vehicle. WEIGHT: 110 pounds. CAPACITY: 160 pounds (model FLC-0500-2) or 300 pounds (m

Peddle Master

The Peddle Master is a hand control for a vehicle's accelerator and brakes designed for use by individuals with mobility and neurological disabilities or lower extremity disabilities or amputation. The controls can be installed in cars, trucks, or vans, and they are intended to allow the user to control the operation of the accelerator and brake pedal in a vehicle with automatic transmission and power brakes. This device can be installed and removed while seated in the driver’s seat without the

Permolock C

The Permolock C is a wheelchair restraint system designed for people with mobility disabilities or spinal cord injury who use the Permobil C400 or C500 power wheelchairs (see separate entries). The Permolock C consists of a locking plate that is mounted on the floor of the vehicle and a spring-loaded pin attached to the wheelchair base. The wheelchair equipped with the pin approaches the locking base from the rear with pin aligned with a slot in the center of the top of the plate. A control bu

Permolock C3

The Permolock C3 is a wheelchair restraint system designed for people with mobility disabilities or spinal cord injury who use the Permobil C300, C350, K300 or K450 power wheelchairs (see separate entries). The Permolock C3 consists of a locking plate that is mounted on the floor of the vehicle and two spring-loaded pins attached to the wheelchair base. The wheelchair equipped with the pins approaches the locking base from the rear with pins aligned to two slots in the top of the plate. The pins

Person Lift

Mobile home lift with chair and step. Skid resistant platform lift attaches to side of recreational vehicle. Standard 48 inch lift travels 40 inches and lifts up to 250 pounds. Lift tube dimensions: 50 inches high by 2.25 inches in diameter. Platform removes for storage. Platform weight: 20 pounds. Platform dimensions 2 inches by 13 inches by 16 inches. Chair lift component of system: seated person is raised and swings into recreational vehicle using double hinged bracket. Aluminum chair removes

Phc-3 Portable Hand Control

The PHC-3 Portable Hand Control is a vehicle hand control designed for use by individuals with lower extremity disabilities or amputation, mobility disabilities, or spinal cord injury. This hand control can be carried in a briefcase or airline carry on luggage when its "legs" are telescoped and folded. The control is designed for use in vehicles with automatic transmissions, including automobiles, light trucks, many specialized industrial vehicles, golf carts, and some arcade games. Power brakes

Pilot Lift

The Pilot Lift is an exterior seat lift designed to adapt to a variety of transportation and mobility applications. It features three-way directional movement that allows comfortable access to a full 360 degrees and a compact mounting system. The user has easy control of the lift from a hand-held control. The lift has a variety of applications including farm tractors and harvesters, small lawn tractors, pick-up trucks, airplanes and boats. There are three different variations of the Pilot Lift.

Pioneer Hybrid Platform Lift (Model Al600)

The Pioneer Hybrid Platform Lift, model AL600, is a platform van lift designed for use by individuals with mobility disabilities or spinal cord injury. This device can lift a power wheelchair or scooter into the back of most SUVs, vans, or minivans. Features include a four-point universal securement system, and remote hand controls. The lift can be installed using existing third-row seating mounts as well as in vans without a third row. POWER: Uses battery and supplied electrical harness with fu

Platform Van Lift

Van lift mounts outside rear door. For individual who does not drive, but needs assistance entering and exiting van. Features nonskid surface platform. Requires manual folding and unfolding of platform. Control push button to raise and lower platform. Fits Chevrolet, Ford and Dodge vans. CAPACITY: 700 pounds. DIMENSIONS: Platform size is 45 inches long, 55 inches wide.

Pneumatic Driving Control

The Pneumatic Driving Control is a hand control for automobiles designed for use by people with lower extremity or neurological disabilities and leg amputees. The air-operated driving controls operate the brake and accelerator pedals. The control box is available in two styles: push for brake, or push for brake and pull for gas. The manufacturer's estimated control effort by the driver ranges from 16 ounces to 3 pounds, or 16 ounces to 4 pounds. The device is compact and does not interfere with

Polavisor Ii

PolaVisor II is a windshield glare screen designed for use by individuals with visual impairments who are still qualified to drive. The screen has a sensor-controlled anti-glare lens shade that changes with the strength of the sunlight as fast as within seven seconds. The lens reduces sunlight brightness up to 80 percent without dimming effect. It absorbs ultraviolet (UV) rays, enhances visual acuity, heightens vision contrast, and reduces eye strain and fatigue. The lens material is made of a m

Portable Control (Model 122)

The Portable Control, model 122, is a portable hand control system designed for temporary use only on rental or other vehicles with automatic transmission, power brakes and steering. This model requires strong arms and hands for operation and must be removed for standard foot use. A nylon carrying case is included.

Portable Left Foot Accelerator

The Portable Left Foot Accelerator is an accelerator pedal for persons with limited or no use of the right leg requiring them to drive with their left leg. It is equipped with a guard to prevent the driver from inadvertently pressing their right foot on the accelerator pedal. The bottom of the base plate has a vinyl gripping system, and the top of the base plate, accelerator pedal and right foot guard have non-skid surfaces. This lightweight portable accelerator can be transferred from one car t

Power Bi-Fold Van Ramp (Models Mf1, Mf1-R, Af1, & Af1-R)

The Power Bi-Fold Van Ramp, models MF1, MF1-R, AF1, and AF1-R, is a van ramp designed for use by individuals with mobility disabilities or spinal cord injury. Made from 6061 Aerospace-grade aluminum , this power bi-fold ramp installs in an existing van, and is available with a wireless remote (MF1-R, AF1-R). DIMENSIONS: 72 x 26 inches (MF1, MF1-R) or 96 x 30 inches (AF1, AF1-R). CAPACITY: 1000 pounds.

Power Door Operator

Electric powered door opener for full-size vans with sliding doors. Includes separate door locking mechanism to draw door tight into body. Kit includes switches and wiring for inside and outside locations. Compatible with Electro Van Lift rotary wheelchair lift.

Power Drivers Seat Base For Van (Model V7)

Power driver seat base for van travels 20 inches back and up to height comparable to that of wheelchair for easy transfer. Seat base rotates with power bearing swivel. After transfer to the seat base, person pushes button to bring seat forward and down to location of original factory installed vehicle seat. Presently used in vans.

Power Emergency Brake Operator

Powered parking brake. Electric powered motor with cable and spool arrangement to operate the emergency brake pedal. Used in situations where the emergency brake is normally foot operated. Includes dash mounted toggle switch.

Power Floor Pan

Van floor elevator to accommodate wheelchair driver attaches to floor of van. Will lower floor up to 6 inches with self centering toggle switch. Positions driver for proper visibility and for driving. Does not move horizontally. Individual wheel cups can also be installed in variety of floor locations for permanent positioning of wheelchair in van. For Ford, Chevrolet and Dodge vans.

Power Headrest

The Power Headrest is a powered headrest and driving control system designed for use by individuals with upper extremity disabilities, severe physical disabilities, or spinal cord injury. This headrest features motorized activation to swing it into position for driving and to the storage position for unencumbered exit and entry into driving position. Its driving control function enables drivers with disabilities that limit hand/finger usage while driving to access turn signals, horn, dimmer, wip

Power Seat Bases

Electric powered seat bases that move seats into position for transfer to and from wheelchairs. Models available for drivers or passengers. Available with a power swivel.

Power Step

DO IT YOURSELF ENTRY --- PURPOSE: To enable an individual with muscular dystrophy to enter a camper. A framework was built of square tubing and hinged to the side of the camper. A removable step was built of smaller square tubing. The power step is powered by a 12-volt cable winch. AUTHOR: Wechsler, K. TITLE: Doing It Yourself. JOURNAL: Quest. WEB SITE: http://www.mda.org/publications/Quest/q113diy.html. REF: Vol. 11, No. 3, May/June 2004. PAGES: 3.

Power Transfer Seat Base - 6 Way Scissor (Model 908D)

The Power Transfer Seat Base - 6 Way Scissor, model 908D, is an adjustable position van seat base designed for use by individuals with mobility disabilities or spinal cord injury. This power base enables the driver's side seat in a full size van to move as much as 16 inches horizontally or 8 inches vertically, and to swivel up to 100 degrees. No alteration of the factory seat is required for installation. OPTIONS: Seat base for drop floor full-size van with OEM power or manual seat. DIMENSIONS (

Power Transfer Seat Base - 8 Way Parallel Arm (Model 858D)

The Power Transfer Seat Base - 8 Way Parallel Arm, model 858D, is an adjustable position van seat base designed for use by individuals with mobility disabilities or spinal cord injury. This power base enables the driver's side seat in a full size or mini van to move as much as 16.5 inches horizontally or 5 inches vertically, and to swivel up to 100 degrees. No alteration of the factory seat is required for installation. DIMENSIONS (HxLxW): 8.25 x 30 x 15 inches. CAPACITY: 300 pounds total combin

Power Transfer Seat Base - 8 Way Parallel Arm (Model 858P)

The Power Transfer Seat Base - 8 Way Parallel Arm, model 858P, is an adjustable position van seat base designed for use by individuals with mobility disabilities or spinal cord injury. This power base enables the passenger's side seat in a full size or mini van to move as much as 13.25 inches horizontally or 5 inches vertically, and to swivel up to 180 degrees. No alteration of the factory seat is required for installation. OPTIONS: Special 858P for drop floor full-size van. DIMENSIONS (HxLxW):

Power Transfer Seat Base - 8 Way Scissor (Model 007)

The Power Transfer Seat Base - 8 Way Scissor, model 007, is an adjustable position van seat base designed for use by individuals with mobility disabilities or spinal cord injury. This power base enables the driver's side seat in a full size or mini van to move as much as 16 inches horizontally or 8 inches vertically, and to swivel up to 100 degrees. No alteration of the factory seat is required for installation. This model is available for a full-size van with an EOM power seat, or for a mini or

Power Transfer Seat Base - Power Swivel (Model 977)

The Power Transfer Seat Base - Power Swivel, model 977, is an adjustable position van seat base designed for use by individuals with mobility disabilities or spinal cord injury. This power base enables the driver or passenger side seat in a full size or mini van to swivel up to 100 degrees. No alteration of the factory seat is required for installation. OPTIONS: Power swivel with 6-way power. DIMENSIONS: Height is 1.75 inches with power swivel or 5 5/8 inches with power swivel with 6-way power.

Power Transfer Seat Base - Slide & Swivel (Model 866D)

The Power Transfer Seat Base - Slide & Swivel, model 866, is an adjustable position van seat base designed for use by individuals with mobility disabilities or spinal cord injury. This power base enables the driver's side or passenger's side seat in a full size van to move as much as 11 inches horizontally and to swivel up to 100 degrees (driver's side) or 180 degrees (passenger's side). No alteration of the factory seat is required for installation. DIMENSIONS (HxLxW): 7 x 25 x 13.75 inches

Powered Door Locks (Models V22 & V22A)

Power door locks for front and rear door. One switch unlocks all three. Allows user to open door of vehicle at touch of switch control. User must have enough strength to push switch.

Powerlift

PowerLift is a bus lift designed for use by individuals with mobility disabilities. This lift raises and lowers a bus passenger in a wheelchair between ground level and the level of the bus floor. It features a compact design and durable construction. WARRANTY: One year limited warranty; extended warranty available.

Pt Driver & Pt Rider

The PT Driver or PT Rider is a minivan with ramp designed for use by individuals with mobility disabilities or spinal cord injury. This is a converted PT Cruiser with a lowered floor, a side-entry ramp, and click-in driver or passenger seats. The van comes with four-point wheelchair restraints and carpeting; commercial-grade non-slip flooring is available. DIMENSIONS (HxLxW): Interior is 56 x 48 x 29.5 inches. The ramp is (LxW) is 32.5 x 44 inches. The door opening height is 50 inches.

Pto Shift Conversion For An International 766 Tractor.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Conversion for engaging and disengaging PTO designed for operators who have difficulty turning the upper torso. The original position of the PTO shift on the International 766 Tractor was behind the driver's seat to the left. The operator had to reach behind the seat with the left hand while turning the torso. Conversion places the shift directly to right of the operator. Two different types of linkage have been used. Mechanical linkage, which includes

Push Button Car Door Aid.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Car door aid is designed to open doors with push button handles. May also be used to open seat belts and recessed handles inside the car door armrests. Aid is constructed by sawing a U bolt in half and screwing one half piece into a small rectangular piece of wood that has had a hole drilled into one end. A small piece of rubber hose is attached to the end of the U bolt to protect the surface of doors. SKILLS REQUIRED: Woodworking. Metalworking. AUTHOR

Push-Pull Quad Control (Model 3700)

The Push-Pull Quad Control is a car driving, hand control designed to assist drivers with muscular disabilities - post polio, muscular dystrophy. It is engineered to require no finger dexterity and needs very minimal use of the bicep and tricep muscles to operate. This supportive driving control is designed to utilize a push-pull motion with positive mechanical connections between driver and vehicle: For gas - pull down; to brake - push forward; and for special situations, the user can apply bot

Pvi Multifold Ramp With Extended Lip (Models Utw630, Utw730, Utw830, & Utw1030)

The PVI Multifold Ramp With Extended Lip, models UTW630, UTW730, UTW830, and UTW1030 (also known as the PVI Utility Ramp), is a portable van ramp designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This folding ramp has an extended hook so that the top of the ramp clears the rear bumper. It separates into two pieces for folding and transport, and it is carried like a suitcase. The ramp has welded construction with an anti-slip, high traction surfa

Pvi Rear Door Ramp (Models Van727 & Van827)

The PVI Rear Door Ramp, models VAN727 and VAN827, is a van ramp designed for use by individuals with mobility disabilities or spinal cord injury. This ramp mounts to the floor of the van inside the doorway. It has three sections and is manually operated with a spring assist. The unit has durable welded construction, with an anti-slip, high traction surface. The ramp accommodates wheelchairs and scooters with various wheel configurations, and it can be operated by one person. The unit stores vert

Q Straint Pocket System (Model Q-5001)

The Q'Straint Pocket System, model Q-5001, is a wheelchair restraint system designed to secure wheelchairs and their occupants in vehicles. The belts have bear clamps to adjust length and hooks to attach to frame of wheelchair and to floor pockets located in the floor of the vehicle. Lap and shoulder belts secure the occupant in the wheelchair. The complete system includes two rear belts, two front belts, , one shoulder belt, one lap belt, one shoulder belt bracket assembly, four floor pocket

Q'straint System (Model Q-5001-T)

The Q'Straint System, model Q-5001-T, is a wheelchair restraint system designed to secure wheelchairs and their occupants in vehicles. This model can be mounted on heavy-duty, floor-mounted aluminum L track (available with or without flange; not included), wheelchair tie-down straps, and occupant shoulder and lap belts. The complete system includes two rear belts, two front belts, one lap belt, one shoulder belt, one driver instruction guide, one instruction adhesive label, and one warranty card

Qrt Retractable Securement System System (Models Q-8100-A1 & Q-8200-A1)

The QRT Retactable Securement System is a wheelchair restraint system designed to secure wheelchairs and their occupants in transit and para-transit buses. This system can be mounted on tracks, walls, swing arms, floors, seats, flip seats, or barriers. The system retracts out of sight when not in use and a hard cover protects it from damage. Model Q-8100-A1 is the deluxe system and includes four QRT automatic retractors, an all new adjustable lap/shoulder belt combination, interchangeable self-t

Quad Driving Control (Model 110)

The Quad Driving Control, model 110, is a hand control system designed for quadriplegics. The unit includes an adjustable wrist support, hand guard and specially adapted switches on hand control. An extra cam system added to hand control makes operation easier if arm strength is limited. Models are available for mounting on either the right or left side of the steering column. Brakes work with a forward push; accelerator works by pulling downward toward the lap.

Quad Fork

The Quad Fork is a steering wheel spinner designed for use by individuals with grasping or upper extremity disabilities or spinal cord injury. The device attaches to the steering wheel and has two long pieces that extend beyond the rim of the steering wheel to provide leverage, and which are adjustable by reshaping the metal insert inside the outer cover. This device can be removed when not required by the driver. WARRANTY: Five years.

Quad Gear Shift Extension (Model 119)

The Quad Gear Shift Extension, model 119, is an extension lever that attaches to the factory installed gear shift lever to enable persons with limited strength or range of motion to shift gears on an automatic vehicle. The device adds six inches to the original lever.

Quad Hand Control (Model 3502)

The Quad Hand Control, model 3502, is a lightweight brushed aluminum alloy hand control with adjustable wrist support for persons with limited muscle control in the arms and hands. The unit also features a hand guard, special dimmer, and horn switches. The device clamps to the lower part of the steering column and to the gas and brake pedals. It may be mounted on either the left or right side, and will not interfere with the normal operation of the vehicle. It is operated by pushing forward for

Quad Key Turners (Models 116-4 & 116-8)

Quad Key Turners, are key holders for vehicle ignition and doors designed to assist persons with limited wrist strength or movement. The holders consist of a metal rod that can hold one key at each end at various angles to provide extra leverage in turning the key. DIMENSIONS: 4-inch (model 116-4) and 8-inch (model 116-8) lengths.

Quick Detachable Hand Operated Clutch Control Assembly For The Case 1290 Tractor.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Clutch assembly for operators who require a hand operated clutch. Custom modification for the Case 1290 tractor. Constructed of 1 inch square steel tubing with steel angles welded onto the end. This configuration hooks over the top of the clutch pedal and is stabilized by the foot clutch shank. The lever is pushed downward to disengage the clutch. A pivoting latch rod at the upper end of the lever can be inserted in a hole drilled in the seat platform

Rails For Bus

---- CUSTOMIZED ADAPTATION --------- PURPOSE: To create custom adapted rails for bus for an individual with Rubinstein-Taybi Syndrome. This individual has a rare syndrome which has resulted in developmental delay and challenging behaviors, and gets very anxious if she doesn’t feel secure. The home which the individual lives has a bus which is used to take the residents to their day placements and on outings at the weekend. Most of the residents use wheelchairs and are lifted in and out of the bu

Raised Top (Models V32 & V32A)

Raised van top is necessary for tall driver in wheelchair to maneuver inside van and to have proper visibility for driving. Variety of sizes for different vans but not all sizes available for all vans. Roof is white fiberglass. Sport Top offers 5 feet of headroom; full size offer 6 feet of headroom; mid size give 5 feet 4 inches. Sport Top has 2 windows and luggage rails. Raised windows available separately.

Rampvan Foldout

Rampvan Foldout is a mini van conversion with ramp designed for use by individuals with mobility disabilities or spinal cord injury. This van conversion is available with a Toyota Sienna, Chrysler Town & Country, or Dodge Grand Caravan chassis. The conversion features a 10-inch drop floor (11 inches on the Toyota Sienna Rampvan) and a powered foldout ramp. Other standard features include a power passenger sliding door; a powder-coated non-slip ramp surface; interchangeable quick-release fro

Rampvan Infloor

Rampvan Infloor is a van conversion with ramp designed for use by individuals with mobility disabilities or spinal cord injury. This van conversion is available with a Toyota Sienna, Chrysler Town & Country, or Dodge Grand Caravan chassis. The conversion features a 9.75-inch drop floor and a power ramp that stows completely under the floor of the cabin, leaving the passenger door accessible for other passengers to enter and exit the van. Other standard features include a power passenger slid

Ready Ramp (Models Rr06, Rr07, Rr08, & Rr10)

The Ready Ramp is a folding van ramp designed for use by wheelchair users. This compact portable ramp unfolds to its full size in three steps and has recessed hinges so the ramp surface is free of obstructions. Construction is welded aluminum with a non-skid surface. DIMENSIONS (LxW): 6 feet x 30 inches open, 42 x 15 inches closed (RR06); 7 feet x 30 inches open, 48 x 15 inches closed (model RR07); 8 feet x 30 inches open, 56 x 15 inches closed (model RR08); 10 feet x 30 inches open, 68 x 15 inc

Recreational Vehicle.

Custom designed recreational vehicle. Swingaway, platform and super arm lifts. Wheelchair accessible toilet and shower. Drive from wheelchair or drivers seat. Many models and floor plans available. .

Remotostart (Model V41)

Remote control engine starter that turns on vehicle engine and heating or air conditioning system from distance up to 400 feet. Defroster included for winter months. Device automatically restarts motor if vehicle stalls. Remotostart automatically goes off if vehicle door is opened or if foot brake is applied to prevent vehicle theft. Operates with push button (operation similar to that of garage door opener. Can be transferred from one vehicle to another. Anti theft provisions built in to device

Removable Hand Operated Clutch Control Assembly For The International 1586 Tractor.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Clutch assembly for operators who require a hand operated clutch. Modifies an International 1586 tractor which has an electric clutch. The control linkage is attached to the regular foot pedal by a nut. A shaft stub is mounted to the left side of the tractor steering console. This acts as a pivot point for the control lever, which is held to the shaft by a pin. Pulling the lever disengages the clutch. The hand control is easily removed to allow operati

Ricon Clearway S-Series Split Platform Lift

The Ricon Clearway S-Series Split Platform Lift is a platform van lift designed for use by individuals with mobility disabilities. This van lift features a fully automatic split platform that folds up to leave the doorway clear. It has a steel frame, a non-skid platform with handrails, automatic inboard and outboard rollstops, an hydraulic pump, a built-in manual backup system, pre-lubricated bearings at all major pivot points, and dual-power cylinders for smooth operation. OPTIONS: Power remote

Ricon Klearvue K-Series Folding Platform Lift

The Ricon KlearVue K-Series Folding Platform Lift is a platform van and bus lift designed for use by individuals with mobility disabilities. The platform folds in half for stowing. When stowed, it provides an unobstructed view of the road for the driver and for passengers. Because the platform folds, it can accommodate scooters and wheelchairs that require a longer platform without modifications to raise the roof or door. Other features include a built-in manual back-up system (hand pump to move

Ricon Reliant S-Series Wheelchair Lift

The Ricon Reliant S-Series Wheelchair Lift is a platform van lift designed for use by individuals with mobility disabilities. This compact van lift has a steel frame and hydraulic pump. Other features include no-lube bearings at all major pivot positions; Sto-Loc technology that locks the platform in the stowed position; automatic inboard/outboard rollstops; a non-skid platform; handrails; a control switch for lowering and raising the lift; and a built-in manual backup system. OPTIONS: Power rem

Ricon S-Series Lift

The Ricon S-Series Lifts are platform van lifts designed to provide access for wheelchair users to vans and public transit vehicles. These lifts feature easy-to-grasp curved handrails, a steel mesh platform, an inboard rollstop that prevents the wheelchair from inadvertently rolling toward the vehicle when the lift is below floor level, an outboard mechanical rollstop that operates even when the vehicle is as much as four feet from the curb, raised platform sides, and patented electrically inte

Right Hand Crossover Signal Controls

The Right Hand Crossover Signal Control is designed for drivers who have lost either their arm, or the use of it. The signal control allows a person to use a single knob to move the steering wheel and access both control signals on one side of their car. The design is unique compared to traditional crossover, in that the clamping design will not come loose on tapered shaft signal arms, will not cause damage to the arm, and can be moved efficiently from one vehicle to another. Additionally, the c

Rollz 2-In-1 Transporter

This Rollz 2-in-1 Transporter is designed for individuals who find it difficult to walk but can walk with the proper walking aid. This 2-in-1 transported is a walker and a wheelchair. The handles turn around to where they are supposed to be for an aid whom pushes the wheelchair. The handles turn back around to where they are supposed to be for using this product as a walker. It crosses doorsteps and curbs easily. Folds up easily to pack in the trunk or closet. Front wheels swivel 360 degrees. Fo

Roosevelt Car Seat

Roosevelt Car Seat is designed to promote safety and comfort for children with special health needs such as cerebral palsy, mobility and neurological disabilities. The Roosevelt Car Seat accommodates children weighing up to 115 lbs. or 62" tall, and can be used with either a lap belt or a lap shoulder belt combination, allowing you to use the Roosevelt Car Seat in any forward facing rear vehicle seat. The car seat is LATCH compliant for children up to 48 pounds, and includes an EZ-Tether connec

Ryno 2500 Hd 4X4 Truck

The Ryno 2500 HD 4X4 Truck is an all terrain mini truck designed for use by individuals with mobility disabilities or spinal cord injury. This heavy duty 4X4 Chevrolet pickup truck has been converted for use by a driver or passenger in a wheelchair. It is available as a passenger's side conversion or a driver's side conversion; some wheelchairs may require modification to work with the driver's side conversion. Each model includes a lift and a lowered floor on the side where the wheelchair sits.

Safe T Spin For Disabled Awareness (Model Da-800)

The Safe T Spin for Disabled Awareness, model DA-800, is a car emergency sign designed for use by individuals with physical disabilities. This sign serves as a signaling device to enable a driver with a disability to summon assistance. The rotating sign bears the wheelchair symbol for disability and is mounted on a magnetic base. The base is designed to enable the unit to be placed on the door of the vehicle. A line attached to the unit prevents it from falling during placement. COLOR: The sign

Safe T Spin For Disabled Awareness (Model Db-400S)

The Safe T Spin for Disabled Awareness, model DB-400S, is a car emergency sign designed for use by individuals with physical disabilities. This sign serves as a signaling device to enable a driver with a disability to summon assistance. The rotating sign bears the wheelchair symbol for disability and is mounted on a magnetic base. A line attached to the unit prevents it from falling during placement. The package includes a poster with "help call police" printed on it for additional help. DIMEN

Save-A-Seat

Save-A-Seat is an automotive seat protector designed for use by individuals with incontinence. The protector also protects against spills and excessive sweating. This removable seat cover provides automotive upholstery on front or bucket seats short-term protection on an as needed basis, utilizing a specially-designed fabric barrier. The device uses a spring roller mechanism to compactly maintain a highly durable protective fabric discretely concealed within a slim dispenser,allowing it to fit u

Scooter Station

The Scooter Station is a wheelchair and scooter restraint system designed for use by individuals with mobility disabilities. Designed for use in full-sized vans, mini vans, and the beds of pickup trucks, this electronically-powered system requires no belts and operates with the touch of a button.

Scott Driving System

The Scott Driving System is a one-hand driving control system designed to enable quadriplegics, paraplegics, persons with limited or no use of one or more limbs, and persons with other disabilities to perform all driving tasks without assistance, including entering and leaving the vehicle. DRIVING CONTROL SYSTEM: A single lever system combines all actual driving functions. Forward movement of the control column actuates the accelerator. Backward movement applies the brakes. Rotation of the mini-

Seat Belt Helper

The Seat Belt Helper is a seat belt extension handle designed for use by individuals with arthritis or upper extremity disabilities. Made of flexible silicone rubber, this device attaches to a vehicle’s seat belt to aid the user to pull the seat belt around the body. DIMENSIONS (LxW): 9 x 3.825 x 7/8 inches. The gripping area extends 6 inches from the seat belt.

Sedona Powerchair Lift

The Sedona Powerchair Lift is a hitch-mounted scooter or powered wheelchair carrier designed for use by individuals with mobility disabilities or spinal cord injury. This lift raises and lowers a scooter or powerchair and is controlled by a key and a toggle switch. The lift is loaded and unloaded by driving on and driving off. The platform has a fully-automatic hold-down system. It tilts automatically on steep inclines and has an integrated suspension system to protect the scooter or powerchair.

Semi Automatic Mini Van Lift-A-Way Lifts

Platform van lift with welded steel construction and semi-automatic operation. Optional handrail. Lift folds and unfolds manually to and from storage position. Lift models to fit most side slide doors on domestic and imported minivans and double rear doors on some domestic minivans. Box frame construction provides rigidity without relying on vehicle side wall strength. Hydraulic pump for quiet operation. Roll- stop on front of platform. Circuit breaker protects against electrical overload. Optio

Semi Automatic Platform Van Lifts (L10 & L40 Series)

Platform van lift with welded steel construction and semi-automatic operation. Optional hand rail. Lift folds and unfolds manually to and from storage position. Lift models fit most side slide, side double and rear van and commercial vehicle doors. Box frame construction provides rigidity without relying on vehicle side wall strength. Hydraulic pump provides quiet operation. Roll-stop on front of platform. Circuit breaker protects against electrical overload. Lift models provide differing amount

Semiautomatic Hydraulic Folding Side & Rear Mount Lift (Models V1C1 & V1C2)

Semiautomatic electric or hydraulic folding side or rear mounted lift for wheelchair users; folds and stores in vehicle. Automatic safety stop. Powered by 12 volt van battery. Includes manual backup system.

Sentinel Series High Top Paratransit Van

The Sentinel Series High Top Paratransit Van is a public transport van designed for use by individuals with mobility disabilities or spinal cord injury. Available floor plans include space for one, two, or three wheelchair users with additional seating for ambulatory passengers. The van is available with side or rear lift doors. Other features include front air conditioning and AM/FM radio with clock. DIMENSIONS (HxLxW): Chassis exterior is 110 x 231 x 78 inches. Interior dimensions are 75.25 x

Sentinel Series Mid Top Paratransit Van

The Sentinel Series Mid Top Paratransit Van is a public transport van designed for use by individuals with mobility disabilities or spinal cord injury. Available floor plans include space for one, two, or three wheelchair users with additional seating for ambulatory passengers. The van is available with either side or rear lift doors. Other features include front air conditioning and AM/FM radio with clock. DIMENSIONS (HxLxW): Chassis exterior is 105 x 231 x 78 inches. Interior dimensions are 71

Shift Conversion And Foot Guard For A Honda Three-Wheeler.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Designed for operators with lower extremity impairments, foot guards help keep one's legs from slipping. A handle, allowing hand shifting, is attached to the foot activated shifter mechanism. The foot guard is constructed of mild steel bar stock and flat steel, with one edge rough or toothed to prevent slipping. The footguard is mounted directly over the existing foot rest, and no major modifications are needed to accommodate the guard. The gear shifte

Shifter Position Conversion And Foot Guard For Honda 200 Sx.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Designed for an ATV operator who has use of the right foot, but not the left. The foot guard is constructed of mild steel bar stock with flat bar stock welded to it for mounting brackets. It is bolted to the bracket holding the existing foot rest and also to the outside end of the footrest. A conversion linkage which allows gear shifting from the opposite side of the ATV is attached to the existing gear shift lever. The linkage passes through the frame

Shoulder Support

The Shoulder Support is a car safety harness designed to provide shoulder support to wheelchair users. The device is made of a steel rod with a standard headrest mounted on top. The device is bolted to the floor of the vehicle. PROTOTYPE DEVELOPMENT: The device was designed by John Duffus for an individual who drives a vehicle from a wheelchair and tends to lean towards the right when making left hand turns. The device provides support for the upper body when maneuvering a vehicle. DIMENSIONS: S

Side Door (Models Sdr626 , Sdr628 & Sdr728)

Side Door, models SDR626, SDR628 and SDR728, is a van ramp designed for use to provide wheelchair or scooter access for van passengers with mobility disabilities or spinal cord injury. It mounts to the floor of the van inside the doorway. When not in use it folds in quarters and stores vertically, leaving the doorway free. A center joint hinge eliminates pinch point and adds strength. Made of welded aluminum with an anti-slip, high traction surface, the unit accommodates wheelchairs and scooters

Side Door Hybrid Platform Lift (Model Al690)

The Side Door Hybrid Platform Lift, model AL690, is a wheelchair or scooter loader for a van designed for use by individuals with mobility disabilities. This lift delivers a powered wheelchair or shorter scooter next to the driver or passenger's door. This lift features one-button operation with a handheld remote and uses second-row seat hardware for installation. DIMENSIONS: This lift has a 33.5 inch vertical reach and requires 32 inches of headroom and a depth of 58.5 inches. The platform is 2

Sidelyer Strap, H-Straps, & Pelvic Strap

The Sidelyer Strap, H-Strap, and Pelvic Strap are restraint and positioning belts designed for use in conjunction with the large foam positioning shapes by the manufacturer (see separate entries). The straps are fabricated of Evazote foam for cushioning ithout bottoming out. The Sidelyer Strap is designed to support the body in proper alignment when positioned on its side. It comes in Adult and Child models, both available with a hole for a gastrostomy tube. The H-Straps form a harness and are u

Single Rider Mobility Cart

The Single Rider Mobility Cart is a personal electric vehicle designed for use by individuals with walking or balance disabilities, arthritis or limited stamina. This low-speed vehicle does not require a driver’s license for most uses. It has one 360-degree swivel seat with adjustable height and forward position, a lap belt and chest support, single right- or left-hand control, wraparound bar, front and rear suspension, and front and rear attachment points. The frame/chassis is made of welded tu

Single Rider Outdoor Mobility Car

The Single Rider Outdoor Mobility Car is a personal electric vehicle designed for use while hunting by individuals with walking, circulatory, or balance disabilities or arthritis or limited stamina. This single rider hunting cart allows the user to hunt whole seated in the vehicle. When the user approaches a target, he or she can position the vehicle, put it in “park,” and then rotate the seat and shoot the target while seated. It has a 360-degree swivel seat with adjustable height and forward p

Skycare Chair

---- PROTOTYPE --------- PURPOSE: To design a prototype of a wheelchair-like mobility tool to be used inside an airplane cabin by individuals with mobility disabilities and/or wheelchair users. Traveling as a wheelchair user and navigating around and onboard an aircraft can be quite a challenge and usually requires assistance from one or more of the flight crew. The Skycare Chair attempts to increase the independence of individuals with lower extremity or mobility disabilities or spinal cord inj

Slideout Telescopic Power Ramp (Model Pf5000)

The SLIDEout Telescopic Power Ramp, model PF5000, is a bus ramp designed for use by individuals with mobility disabilities. This ramp provides access to low-floor buses and tucks away when not in use. The ramp is made of stainless steel and aluminum and features a stainless steel enclosure and an electric ball-screw drive system, a solid state PWM electronic controller, proximity switches, current-limiting circuitry to protect the drive system from damage, and manual back-up. Ramp movement stop

Small Item Storage Solution For Van

DO IT YOURSELF ENTRY --- PURPOSE: To enable an individual with Friedrich's ataxia to carry small items in a van which might get entangled in wheelchair wheels. Attach 3M picture hangers to the wall of the van within reach. They can used to hold a cell phone charger, coffee mug, and other small items. MATERIALS: 3M Picture Hangers. AUTHOR: Labbe, A. TITLE: Quest Extra: Doing It Yourself. JOURNAL: Quest. WEB SITE: http://www.mda.org/publications/quest/extra/qe14-5_diy.html REF: Volume 14, Number 5

Smart Shift

Smart Shift is a driving control system designed for use by individuals with upper extremity disabilities. This stand-alone electronic gear selector includes a touchpad control and actuator that offer touch-button access to park, reverse, neutral, and drive. A Drive 2 option can be configured for low gear in most applications. Each raised tactile button on the touchpad features center illumination and a universal icon; the buttons are widely spaced to prevent inadvertent function activation. Thi

Smooth Floor Covering (Wood Wheelchair Flooring)

Smooth floor covering of Luan Mahogany plywood provides smooth surface over factory installed metal van floor for wheelchair access. Provides easier wheelchair movement inside van.

Solorider 3400

The SoloRider 3400 is an adapted golf cart and personal electric vehicle designed for use by individuals with walking or balance disabilities, arthritis or limited stamina. This single rider golf car allows the user to play golf without getting out of the cart. When the user approaches a golf ball, he or she can position the vehicle, put it in “park,” and then rotate the seat and hit the ball while seated. The frame/chassis is made of tubular steel with powder-coated finish and has a 7-inch grou

Space Saver Take-Apart Scooter Lift (Model Asl-325)

The Space-Saver Take-Apart Scooter Lift, model ASL-325, is a trunk mounted wheelchair alternative loader for persons with mobility disabilities using scooters. The lift raises and stores scooters in cars with limited trunk space. It is height and length adjustable to fit any trunk size, and can lift scooters weighing up to 200 pounds. The Space-Saver is easily assembled and disassembled in three simple steps, with the heaviest part weighing just 13.5 pounds.

Special Tomato Mps Car Seat

The Special Tomato Multi-Positioning Seat Car Seat Version is a child's car seat designed for use by children and youth with physical disabilities. The seat has adjustable seat, head, and back cushions and offers a choice of regular or extended size seat cushions, allowing the seat width and depth to be adjusted to accommodate the child's growth. Other features include a seat shell, a latch strap and tether strap for in-vehicle use, and safety attachment straps for use outside of a vehicle. The

Spinner Knob

The Spinner Knob is a steering wheel spinner designed for use by individuals with grasping or upper extremity disabilities or spinal cord injury. It attaches to the rim of the steering wheel, and features a large knob that can be grasped, pushed, or pulled to control the wheel. The spinner can be removed from the steering wheel when not required by the driver. . WARRANTY: Five years.

Spinner Knob (Model 3520B,3520G & 3520W)

The Spinner Knob, model 3520B, 3520G, and 3520W, is a steering wheel spinner designed for use by individuals who use driving hand controls or who have upper extremity disabilities. Designed to assist drivers turn the steering wheel, this device presses firmly against the palm of the hand offering added strength and control for ease in driving. COLORS: Black (Model 3520B, gray(Model 3520G, or woodgrain (3520W).

Spirit Scooter Lift (Models Flc-0400-2 & Flc-0400-3)

The Spirt Scooter Lift is a hitch mounted scooter lift designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. The lift mounts to a Class II (model FLC0400-2) or Class III (model FLC-0400-3) receiver hitch. It can be configured for three or four wheel scooters. The scooter is automatically clamped after being driven onto the platform without additional tie-downs. The platform is weight-sensitive and automatically folds up and out of the way when lift

Sport Top Sentinel Paratransit Van

The Sport Top Sentinel Paratransit Van is a public transport van designed for use by individuals with mobility disabilities or spinal cord injury. Available floor plans include space for one, two, or three wheelchair users with additional seats for ambulatory passengers. This Ford van conversion has side or rear lift doors for wheelchair entry. Other features include front air-conditioning and an AM/FM radio with clock. OPTIONS: 4.2L-V6, 5.4L-Triton V8 Gas or Compressed Natural Gas (CNG), 6.8L-T

Stage 1 Overlay Cushion

The Stage 1 Overlay Cushion is an alternating air pressure flotation seat cushion designed to prevent pressure sores for people with lower extremity or mobility disabilities, spinal cord injury and others who are at risk for pressure sores. It can be used in a wheelchair, automobile seat, or other chair. The bottom of the cushion has a cling type surface. The cushion is covered in breathable fabric treated to resist soil and stains. A clear vinyl plastic case protects the pump from spilt coffee

Stand Ease

Stand-Ease is a car transfer aid designed for use by individuals with lower extremity or mobility disabilities. This device assists individuals who have difficulty getting in and out of a car because of the low seat. To enter a car with this device, the user sits down on the raised bar in the doorway and presses the Down switch. The user's bottom is gently lowered to seat level, and the user then rotates the legs into the vehicle. To exit, the user rotates the legs out of the car, presses the Up

Stand-N-Ride (Model Snr And Snr2)

The Stand-N-Ride, model SNR and SNR2, is a 3-wheeled scooter designed for use by individuals or couples with lower extremity and mobility disabilities. It can used while standing or sitting. FRAME (LxWxH): 36.3 x 25.3 x (48-36) inches with anti-tippers,It can be disassembled into two parts for transport or storage. The Stand-N-Ride has an underbody ground clearance of 2.75 inches and a turning radius of 22 inches. The only available color is black. An optional detachable basket can be attached i

Standard Folding Wheelchair Carrier (Model Wc002M-52)

The Standard Folding Wheelchair Carrier, model WC002M-52, is a hitch mounted steel wheelchair carrier designed to carry a manual, folding wheelchair on the back of a car. The device mounts to a standard class 1 trailer hitch on a car. An anti-sway bracket helps the carrier from pivoting on the hitch. The carrier is bolted on and screwed with a wingnut. The chair is then lifted into position, and a locking arm is slid down tight and secured with a strap (included). A standard padlock will fit thr

Starcraft Chevrolet Venture Lowered Floor Mini Van

The Starcraft Chevrolet Venture Lowered Floor Mini Van is a mini van conversion with ramp designed for use by individuals with mobility disabilities or spinal cord injury. In this wheelchair-accessible van conversion, the original factory floor is replaced with a floor that is 13 inches lower. The lowered floor is flat and unobstructed from the rear sofa to the front seat positions. The curbside entry door is modified to accommodate a fold-away ramp, which folds up and swings out of the way when

Starcraft Lowered Floor Full Size Ford Van

The Starcraft Lowered Floor Full Size Ford Van is a van conversion designed for use by individuals with mobility disabilities or spinal cord injury. In this wheelchair-accessible van, the original factory floor is replaced with a lowered floor that provides a drop of 6 inches. The floor is completely flat and unobstructed from the rear sofa bed to the firewall under the dashboard. The double swing-out curbside entry doors accommodate most wheelchair lifts (not included), and allow roll-in, roll-

Startracks Accessible Motor Home

Startracks Accessible Motor Homes are custom adapted motor homes designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. Motor homes and busses of different lengths can be adapted for wheelchair access with a variety of floor plans, lifts, doors, tubs, and other accessories.

Startracks Accessible Travel Trailer

The StarTracks Accessible Travel Trailers are custom-built, wheelchair accessible travel trailers designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. Some trailers include a wheelchair lift. DIMENSIONS: Available lengths range from 26 to 41 feet.

Steering Control Hook Grip (Model 3521)

The Steering Control Hook Grip, model 3521, is a spinner ring designed for use by individuals who use a two-finger prosthetic hook when driving. The device attaches to a bar mounted on the steering wheel in a ball bearing spinner receptacle. To secure the steering wheel for ease in handling, the user places one finger on the outside of the spinner ring while postioning the other finger on the inside.

Steering Control Palm Grip (Model 3523)

The Steering Control Palm Grip, model 3523B, is a steering wheel spinner designed for use by individuals who use driving hand controls or who have upper extremity disabilities. This lightweight aluminum wrap adjusts to fit the hand and offers a firm strength that holds the shape for secure steering control, and a raised finger rest protects the fingers from contact with the steering wheel. Other features includes a soft sheepskin liner that protects the hands and provides warmth in winter.

Steering Control Tri-Pin Grip (Model 3522)

The Steering Control Tri-pin Grip, model 3522, is a steering spinner bar designed for use on vehicles with power steering for persons with no tensor control in the wrist. This device is a three-pin grip designed to comfortably position and secure the hand and wrist on the steering wheel. The pins are lightweight and adjustable, and attaches across the diameter of the steering wheel. An available counter weight diminishes the weight of the grip so that it can be mounted on either side of the ste

Steering Control V-Grip (Model 3524)

The Steering Control V-Grip is a wheel spinner designed for use by quadriplegic drivers with some tensor control. Designed with a foam-grip single pin and foam-covered wrap, this device provides backhand support that secures the hand in a comfortable position. The unit is mounted onto the steering wheel and can be adjusted to the user’s desired steering grip.

Steering Knob (Model Mp20A)

Steering knob spinner allows driver to steer vehicle with one hand. Cast aluminum ball bearing base attaches to steering wheel with bolts and clamps (hairpin lock). Clamps adapt to shape of steering wheel. Knob is upright to steering wheel and can be positioned for driver's needs. Knob removed by pulling pin, easily transferred to other vehicles. Easy installation.

Stepless Easyfold Ramp (Models 30060-090, 30060-120, 30060-150 & 30060-180)

The Stepless EasyFold Ramp, models 30060-090, 30060-120, 30060-150 and 30060-180, is a portable ramp designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and others who use wheelchairs and scooters. This single-fold ramp can be folded and carried with the attached carrying handles or stored. When unfolded, the ramp provides a solid non-skid surface. The ramp can be positioned and removed as needed to overcome minor height differences. Models 30060-1

Stepless Easyfold Telescopic Ramp (Models 30070-180, 30070-210, 30070-240, & 30070-300)

The Stepless EasyFold Telescopic Ramp, models 30070-180, 30070-210, 30070-240 and 30070-300 is a portable ramp and van ramp designed to provide wheelchair or scooter access to structures and vans for people with lower extremity or mobility disabilities or spinal cord injury and others who use wheelchairs and scooters. The length of the ramp is adjustable so it can be used to provide access between two surfaces with a variety of height differences. The telescopic function prevents finger pinching

Stepless Lifting Platform (Models Lp12)

The Stepless Lifting Platform, model LP12, is an exterior wheelchair lift designed to lift individuals who use wheelchairs or who have walking disabilities on and off trains. This unit can be transported while folded directly to and used on any railway platform; positioning is accomplished using the built-in clontrol arm. The lifting platform wheels are equipped with a central braking system. Made of weatherproof materials, this unit can be stored under a variety of conditions. POWER: Uses a bu

Stepless Lite Ramp (Models 30100-070, 30100-085, 30100-125, 30100-165 & 30100-205)

The Stepless Lite Ramp, models 30100-070, 30100-085, 30100-125, 30100-165, and 30100-205, is a portable ramp designed for use by individuals with mobility disabilities or spinal cord injury. Made of glass and graphite fiber, the Stepless Lite Ramp is lightweight and folds lengthwise for transport and storage. It has a non-skid surface with a raised edge on each side, and a carry handle on one side for transporting the ramp when folded. It can be used by passengers on public transport, including

Stepless Wide Folding Ramp (Models 30040-150, 30040-200, 30040-250, & 30040-300)

The Stepless Wide Folding Ramp, models 30040-150, 30040-200, 30040-250 and 30040-300, is a portable ramp designed for use to provide wheelchair or scooter access for people with lower extremity or mobility disabilities or spinal cord injury and others who use wheelchairs and scooters. This ramp's increased width is intended to provide increased safety for users of scooters and electric wheelchairs and their helpers. The unit can be kept permanently in position or always used in the same place. T

Stisim Drive M100-Ot & M100Ws-Ot

The STISIM Drive M100-OT & M100WS-OT is a driving simulator and assessment and evaluation system designed for use by an occupational therapist (OT) to assess patients in rehabilitation hospitals and clinics. The system includes STISIM Drive Software; 1 (model M100-OT) driver display screen or 3 (M100WS-OT) driver display screens; 1 Dell computer work station (M100-OT) or 3 Dell work stations (M100WS-OT) with Microsoft Windows and high performance nVIDIA graphics card; 1 operator display scre

Stisim Drive M300-Ot & M300Ws-Ot

The STISIM Drive M300-OT & M300WS-OT is a driving simulator and assessment and evaluation system designed for use by an occupational therapist (OT) to assess patients in rehabilitation hospitals and clinics. The system includes STISIM Drive Software; 1 (model M300-OT) driver display screen or 3 (M300WS-OT) driver display screens; 1 Dell computer work station with Microsoft Windows and high performance nVIDIA graphics card; 1 operator display screen; a STISIM Drive high fidelity advanced cont

Stisim Drive M300Ws-Ot-Console

The STISIM Drive M300WS-OT-Console is a driving simulator and assessment and evaluation system designed for use by an occupational therapist (OT) to assess patients in rehabilitation hospitals and clinics. This portable system is mounted on a wheeled base and includes 1 Dell computer work station with Microsoft Windows, STISIM Drive Software, and a high performance nVIDIA graphics card in a lockable computer bay; 3 driver display screens; 1 operator display screen; an ergonomic auto seat with sa

Superarm Lift 2000

The Superarm Lift 2000 is a steel van lift designed without a platform for use with manual and powered wheelchairs, or scooters (with optional harness attachments). Instead of a platform, the wheelchair and its occupant are raised or lowered by means of a pivoting arm. The lift is designed to work without modification to the vehicle and without obstructing the doorway to other passengers. The wheelchair tips backwards for occupant's head clearance through the van door. Operation toggle switches

Supergrade Iv Hand Control (Model 100)

The Supergrade IV Hand Control, model 100, is a control mechanism for operating a vehicle with the hands. The controls can be installed in cars, trucks, or vans, and controls the operation of the accelerator, brakes, headlight dimmer, and hand. Special mounting brackets are available for mounting on different cars. The controls can be ordered for mounting on either the right or left side of the steering column. OPTIONS: Horn and headlight dimmer control.

Sure Grip Push / Rock

The Sure Grip Push/Rock is a driving hand control designed to ease muscle fatigue for persons with muscular disabilities. This controller is engineered to allow the user to pull the handle back to accelerate and to push forward for braking. It is located beneath the steering wheel on the left hand side. It enables the driver to keep both hands on the wheel, and it offers the user the opportunity to free the right hand to either operate controls on the dashboard, such as the air conditioning and

Sure-Lok Fe500 Series System

The Sure-Lok FE500 Series System is a wheelchair restraint system designed for use by individuals with mobility disabilities or spinal cord injury. The system includes over-center buckle and/or cam buckle straps with a minimum breaking strength of 6,000 pounds and 5,000 pounds, respectively. Most kits available in this system have vehicle anchoring hardware that is "positive-locking" to ensure that when the system is properly installed, the strap assemblies cannot be inadvertently released or di

Sure-Lok Heavy Duty Series A Track (Models 2025 & Fe702-01)

Sure-Lok Heavy Duty Series A Track is hardware for a wheelchair restraint system designed for use by individuals with mobility disabilities or spinal cord injury. The track is made of 11-gauge high-strength steel coated with a rust-inhibiting powder, and comes in vertical (model 2025) or horizontal (model FE702-01) styles. OPTIONS: Special length track is available. COLORS: Track is gun metal grey. DIMENSIONS: Horizontal and vertical tracks are both available in 5 or 10 feet sections. WEIGHT: A

Sure-Lok Heavy-Duty Series A Floor Plate (Model Fe200740)

Sure-Lok Heavy-Duty Series A Floor Plate, model FE200740, is hardware for a wheelchair restraint system designed for use by individuals with mobility disabilities or spinal cord injury. This low profile plate is made of zinc-plated steel. OPTIONS: A floor plate kit is available that inlcudes one model FE200740 floor plate, one backing plate, and bolts, nuts, and washers (four of each). WEIGHT: 1 pound.

Sure-Lok Integrated Combination Belt (Model Fe200727)

The Sure-Lok Integrated Combination Belt, model FE200727, is a wheelchair restraint system designed for use by individuals with mobility disabilities or spinal cord injury. This system combines a shoulder belt and an integrated lap belt in a fully retractable unit. The unit retracts to the vehicle sidewall; a Velcro strap is provided to keep the belt ends up against the vehicle sidewall when not in use. The retractor mechanism can be mounted directly to the vehicle floor or sidewall, or into Ser

Sure-Lok Integrated Lap Belt (Model Fe200595)

The Sure-Lok Integrated Lap Belt, model FE200595, is a wheelchair restraint system designed for use by individuals with mobility disabilities or spinal cord injury. This belt is intended for use with the FE500 Series Wheelchair Securement System only (see separate entry). It attaches directly to the rear strap assembly of the wheelchair securement system, and provides an occupant restraint system that is an integrated part of the wheelchair securement. Its restraint capability is dependent upon

Sure-Lok Parallel Lap Belt (Models Fe200594, Fe200600, Fe200601, Fe200612)

The Sure-Lok Parallel Lap Belt is a wheelchair restraint system designed for use by individuals with mobility disabilities or spinal cord injury. This belt attaches directly to the floor track or plates to secure the passenger separately and independently from the wheelchair securement system. The belt's anchoring hardware is positive-locking to ensure that the belt assemblies cannot be inadvertently released or disengaged. A single push-button function allows the release and evacuation of the o

Sure-Lok Series L Single Bolt Floor Plate (Models Fe200784 & Fe200844)

The Sure-Lok Series L Single Bolt Floor Plate is hardware for a wheelchair restraint system designed for use by individuals with mobility disabilities or spinal cord injury. Both plates have a track section made of stainless steel and come with mounting hardware. Model FE200784 is a surface mount plate and comes with an impact-resistant, plastic ramped collar. Model FE200844 is a flush mount plate and comes with a stainless steel case. WEIGHT: Both models weigh one pound.

Sure-Lok Series L Track

Sure-Lok Series L Track is hardware for a wheelchair restraint system designed for use by individuals with mobility disabilities or spinal cord injury. Track is made of aluminum with a natural finish, and is available in heavy-duty or medium-duty weights. Both the heavy-duty and medium-duty track are available in plain style or with flanges or flanges and mounting holes (100-inch length); with four countersunk holes (8 foot length); or with two holes (9 foot section). Medium-duty track is also a

Sure-Lok Shoulder Belt (Models Fe200599, Fe200604, Fe200604L, Fe200613, Fe200710, Fe200710L, Fe200716, Fe200732)

The Sure-Lok Shoulder Belt is a wheelchair restraint system designed for use by individuals with mobility disabilities or spinal cord injury. Models FE200599, FE200613, FE200716, and FE200732 are non-retractable shoulder belts that can be attached to a section of track mounted on the vehicle sidewall. Models FE200599 and FE200732 are designed for use with Series L track; models FE200613 and FE200716 are designed for use with Series A track (see separate entries). These models are intended for us

Swing Out Lift

The Swing Out Lift is a rotary van lift designed to lift individuals in wheelchairs into vans. Minimal space is needed between parked vehicles to operate the lift with side entry. Controls are mounted on a safety bar and the lifts have a safety backup system and beltless drive. The lift has an integral Electro brake mechanism. The unit is completely assembled and wired at the factory. The installation is such that it may be done by the owner. OPTIONS: There are models with sliding side doors or

Swivel Cushion

The Swivel Cushion is a transfer aid designed for use by individuals with mobility disabilities. Made of foam, this portable disk rests on a .25-inch plywood base and rotates 360 degrees to assist with transfers from chairs and cars. DIMENSIONS: 15 inches in diameter x 1 inch high. CAPACITY: 800 pounds. COLOR: The velour cover is grey.

Swivel Cushion (Model 77142)

The Swivel Cushion, model 77142, is a swivel seat designed for use by individuals with back and hip problems. This lightweight, portable cushion rotates so that the user's back can be kept straight while turning, thereby taking pressure and strain off the back and hips. It consists of a foam cushion on a turntable base of 1/4-inch plywood, with a washable velour cover. CAPACITY: 800 pounds. DIMENSIONS: 15-5/8 inches in diameter. WEIGHT: 4 pounds. COLOR: Velour cover is gray.

Swivel Cushion (Model Ha-4781)

The Swivel Cushion, model HA-4781, is a transfer aid designed for use by individuals with lower extremity or mobility disabilities or arthritis. This cushion helps the user to turn when getting in or out of a car, wheelchair, or bed. It has a washable soft fleece top cover. DIMENSIONS: 405 millimeters in diameter x 55 millimeters high. WEIGHT: 1.5 kilograms.

Swivel Seat

The Swivel Seat is a swivel seat designed for use by persons with low back pain, lower extremity disabilities, arthritis, or other physical disabilities. This round seat is lightweight and portable with a cushioned top. DIMENSIONS: The seat is 15 inches in diameter x 0.75 inch thick.

Tailgate Lifter

CUSTOM ADAPTATION PURPOSE: To enable an individual with mobility and neurological disabilities to open a lift-up station wagon tailgate to access a scooter lift. A spring-loaded arm was mounted inside the tailgate on the same side as the scooter lift. The arm assists in pushing the door open during the first thirty centimeters of opening before the vehicle's built-in gas struts took over. A roller on the end of the arm rolls against the tailgate as it rises. The plastic door lining was reinforc

Tailgater Pick-Up Truck Lift (Models Flc-0300-T25 & Flc-0300-T40)

The Tailgater Pick-Up Truck Lift is a wheelchair or scooter loader for pick-up trucks designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This powered lift with motorized rotation and a powered boom extension enables a power chair or scooter to be lifted from the cargo area of a pick-up truck and positioned beyond the lowered tailgate or next to the truck. Adjustable limit switches automatically stop rotation to prevent lift contact with the vehic

Thomashilfen Thevo Twist Seating System

Thomashilfen Thevotwist Seating System is a manual stroller designed for use by children with lower extremity, mobility, or neurological disabilities or spinal cord injury. Thomashilfen thevotwist stroller gives optimum support to child while allowing the possibility for small trunk movements. While seated in the Thevotwist stroller, users are able to use their arms and hands while being supported. The Stroller incorporates Micro-Stimulation technology and Balance Safety System. Thevotwist Stro

Three Keys Turner (Model Ha-4110)

The 3-Keys Turner, model HA-4110, is a key holder designed for use by individuals with grasping or fine motor disabilities. The molded plastic turner holds three keys and is designed to fit keys to give a larger grip and stronger leverage for turning a key in a lock. Keys fold down when not in use. DIMENSIONS: 120 millimeters long. WEIGHT: 53 grams.

Tibby's Freedom

Tibby's Freedom is an all terrain cart designed to offer persons with muscular or mobility disabilities the ability to interact with their peers in a variety of environments. Designed for accessibilty, this cart is intended for on and off road use (i.e. beach, gravel, water, snow and ice) and is engineered to be environmentally safe. It can be transported in a van, truck or tilt trailor and can be loaded by a single person. It features front and rear wheel air-ride suspension; five point harness

Tie Tech 700 Series Restraint System

The Tie Tech 700 Series Restraint System is a wheelchair restraint system designed to provide secure tie down for people who travel in wheelchairs in vehicles. The system includes tracks that mount securely to the floor of any vehicle. The torso harness straps and lap strap attach independently to the tracks, behind the passenger and then snap together in the front, forming one unit. Wheelchair straps, two on each side to form a four-point system, attach from the wheelchair to the tracks in fron

Tilt'n'tote (Model 001)

The Tilt'N'Tote, model 001, is a hitch-mounted wheelchair carrier designed to carry manual, folding wheelchairs on the bumper of cars. This device is made of steel and attaches to a standard Class 2 or 3 trailer hitch. It fits wheelchairs measuring up to 15 inches when folded. The carrier has an anti-sway bracket which can be installed or removed from a standard trailer hitch easily. To use, the release bar is pulled to permit the rack to tilt to the ground. The wheelchair is wheeled onto the Ti

Tilt'n'tote Plus (Model 004L)

The Tilt'N'Tote Plus, model 004L, is a hitch-mounted wheelchair carrier designed for use by individuals with mobility disabilities or spinal cord injury. It can be used to transport most pediatric and folding electric power chairs, including chairs up to 15.5 inches wide. The front saddle is adjustable to accommodate most lengths. The lift can be mounted on a Class 1, 2, or 3 hitch. CAPACITY: 100 pounds.

Tiny Tote 100 Manual Wheelchair Carrier

The Tiny Tote 100 Manual Wheelchair Carrier is a hitch-mounted wheelchair carrier desiged for use by individuals with mobility disabilities. This unit is used for transporting folding manual wheelchairs. The folded chair is placed on the platform, then the platform is tilted into place and the adjustable hold down arm secures the wheelchair. One handle is used to release the lift for both loading and unloading. The lift itself folds down so the user can access the vehicle's tailgate or lift gate

Toggle Switch Controlled Electrical Clutch For The White 4-2104Wd Tractor.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Electrical clutch assembly for operators with upper and lower extremity impairments, such as quadriplegia. Custom modification for a White 4-210 4WD tractor, uses an electric actuator that can be operated with a dash mounted toggle switch. A clevis pin that connects the foot pedal to the internal clutch assembly was replaced with a pin that extends about two inches to the outside of the linkage. A 12 volt electric actuator is installed on the side of t

Tote Economy Carrier (Model 003)

The Tote Economy Carrier, model 003, is a hitch-mounted wheelchair carrier designed for use by individuals with mobility disabilities or spinal cord injury. This non-folding carrier can be used to mount any standard folding wheelchair using a Class 1, 2, or 3 hitch. CAPACITY: 75 pounds.

Touch Control System (Model 8000H)

System has a vacuum operator for the brake pedal and a vacuum operator for the accelerator pedal. Operators are controlled by a single control handle on the control module which is about 3 inches by 5 inches by 8 inches. Control module can be mounted on the door in front of the arm rest, on the engine housing or bracket attached to the engine housing of a van, or on a bracket to the right of the steering wheel in a sedan. 2 to 4 pounds of force are required to operate the accelerator by moving t

Tracker Inside Lift

The Tracker Inside Lift is a scooter and wheelchair loader designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This lift has a drive-on lifting platform for power chairs and scooters, with two docking system options, the Dock 'N' Lock positive self-guiding manual release docking system and a strapping system. Once the power chair or scooter has been secured to the lifting platform, it is lifted and stowed inside the vehicle's cargo area. This lift

Transit Rider R-5500 Series

Semi-automatic wheelchair lift, electric/hydraulic powered. 31 inch lift travel. Fits in vans with 40 inch doorway width. Overall platform size 32 inches wide by 45 inches long. 47.5 to 61.5 inch maximum entry height via 4 models. 7 second lift time. All steel frame construction. 130 amp maximum load electric motor with hand pump backup. Pendant switch operation by attendant only. CAPACITY: 800 pound maximum lifting capacity.

Tri Pin Quad Grip Spinner (Model Mp22A)

Tri post (three pin) quad steering spinner for quadriplegics. Posts mount at right angle into adjustable slots in T shaped base. Base is cast aluminum ball bearing and clamps to steering wheel. Spinner positioned at right angle to steering wheel. Device designed for quadriplegics with little or no tensor control. Device grips hand at wrist so wrist cannot pull free. Hand can be lifted up and out of device at will.

Tri Pin Steering Device

The Tri Pin Steering Device is a steering wheel spinner designed for use by drivers with grasping or upper extremity disabilities or spinal cord injury. This device attaches to the rim of the steering wheel. It features three rods for grasping, one on the rim and two slightly off the rim. This device can be removed when not required by the driver. WARRANTY: 5 years.

Tumble Forms Carrie Seat (Models 4641L, 4641M, 4641S, & 4641Sa)

The Tumble Forms Carrie Seat, models 4641L, 4641M, 4641S & 4641SA, are positioning seating systems designed for insertion in mobility systems such as strollers, wheelchairs, or in vehicles. They may also be used at home or in school. The seats come with an adjustable footrest, headrest, and tray. Standard features include an anti-thrust seat to stabilize the pelvis; a seat back which articulates 20 degrees to accommodate abnormal trunk tone; an adjustable footrest to maintain hip, knee, and

Turn Signal Adapter (Model 106)

The Turn Signal Adapter, model 106, is a right hand directional signal extension lever that allows the driver to operate the directional signal with the right hand. The device clamps to the base of the factory installed directional signal lever. Manufacturer recommends mounting the adapter to metal or polymers as some thin plastics may crack. The adapter will not interfere with normal operation. The Turn Signal Adapter will accommodate a turn signal base thickness of up to 0.75 inch in diameter.

Turn-Alarm (Models 252, 262, U-1, & U-2)

The Turn-Alarm is a turn signal alert device designed for use by individuals with hearing disabilities. Models 252 and 262 are designed to replace the existing turn signal flashers and are recommended for use in motor homes, vehicles towing trailers and fifth wheels, and vehicles with replacable turn signal flashers. With the device installed, an audible beep is heard as long as the turn signal is on. The unit beeps in the same intervals that the flashers flash. Model 262 has a larger heavy-duty

Turning Cushion (Model Ha-4780)

The Turning Cushion, model HA-4780, is a transfer aid designed for use by individuals with lower extremity or mobility disabilities or arthritis. This foam-padded cushion swivels 360 degrees in any direction to help the user in rising from a seated position. The cushion can be used in a vehicle or on a chair. Its removable cover is water washable. DIMENSIONS: 390 millimeters in diameter. WEIGHT: 1 kilogram. COLOR: Gray.

Two-Pole Dimmer Switch (Model 3550) And Single Pole Dimmer Switch (Model 3551)

The Two-Pole Dimmer Switch, model 3550, and Single Pole Dimmer Switch, model 3551, are remote headlight dimmer controls. A toggle switch mounts to the dash board for hand operation. The unit is made of a lightweight brushed aluminum alloy. The two-pole switch allows normal use of the factory-installed dimmer switch; the single pole switch deactivates the floor dimmer system and transfers it to dashboard. WARRANTY: Contact manufacturer for details.

Ultimate Mobility Van & Ultimate Mobility Truck

The Ultimate Mobility Van and Ultimate Mobility Truck are van or truck conversions designed for use by individuals with mobility disabilities or spinal cord injury. All vans and trucks are custom made conversions of full size vans from General Motors or Ford Motor Company, or mini-trucks from GMC, Ford, or Dodge. Options include lifts, ramps, hand controls, tie downs, and other driving aids.

Uni-Lite

The Uni-Lite is a wheelchair lift for vans designed to ensure smooth, safe entry and exit for wheelchair users. With its compact design and large, non-skid, .25-inch thick aluminum platform, this lightweight conversion loader is adjustable to fit most van doors and is intended to maximize passenger space. Operated by a high-torque electric motor and direct gear drive, it features twin handrails with a control switch, a high-strength, aluminum alloy construction and a built-in manual backup syste

Universal Auto Grip

The Universal Auto Grip is a car transfer aid designed for use by individuals with mobility disabilities. This heavy-duty, wide steel universal handle is designed to hook securely inside the U-shaped striker bracket on a car or truck door frame, providing leverage and support as a driver or passenger enters or exits a vehicle. This device has a non-slip hand grip. DIMENSIONS: 8.25 inches long. GUARANTEE: 90-day satisfaction guarantee.

Universal Auto Grip And Flashlight

The Universal Auto Grip and Flashlight is a car transfer aid designed for use by individuals with mobility disabilities. This heavy-duty steel universal handle is designed to hook securely inside the U-shaped striker bracket on a car or truck door frame, providing leverage and support as a driver or passenger enters or exits a vehicle. It has a a flashlight with nine bright LED bulbs on the end opposite the hook. This device has a non-slip hand grip around the shaft between the hook and the fla

Universal Carrier (Model Wc010M-52)

The Universal Carrier, model WC010M-52, is a hitch mounted carrier for front or rear drive scooters or powered wheelchair alternatives, including batteries. The device mounts to a Class 3 (heavy duty), reinforced Class 2, Reese, or Draw-Tite frame hitch. The carrier platform is tipped down to load the mobility aid (scooters should be backed onto it), then tipped in the opposite direction and locked into place. Straps hold the mobility aid securely. The carrier is made of steel and steel grating

Universal Inside Lift (Model Al200)

The Universal Inside Lift, model AL200, is a wheelchair or scooter van loader designed for use by individuals with mobility disabilities or spinal cord injury. This is a heavy-duty lifter for heavier scooters and wheelchairs. It has an adjustable base that fits most vehicles on either side, and it disassembles into three components for stowage. It has a boom range of 360 degrees. POWER: Powered by the supplied electrical harness. The harness has full-length leads that attach directly to the bat

Universal Inside-Out Lift (Model Al065)

The Universal Inside-out Lift, model AL065, is a wheelchair or scooter van loader designed for use by individuals with mobility disabilities or spinal cord injury. This Class II or III hybrid mounts outside the vehicleand puts the scooter or chair inside, using a boom with a range of 100 degrees. The loader features weather resistant construction and a selection of docking devices for every scooter or chair. POWER: Uses battery and supplied electrical harness with full-length leads that attach

Universal Power Chair Lift (Model Al500)

The Universal Power Chair Lift, model AL500, is a hitch-mounted wheelchair carrier designed for use by individuals with mobility disabilities or spinal cord injury. This outside chair lift has an aluminum deck and automatic tensioners. It works on a Class II hitch-equipped vehicle with a hitch from 5 to 19 inches high, and supports power chairs with a maximum width of 28.5 inches. POWER: Uses battery and supplied electrical harness with full-length leads that attach directly to the battery. OPTI

Universal Scooter Lift (Model Al100)

The Universal Scooter Lift, model AL100, is a hitch-mounted scooter carrier designed for use by individuals with mobility disaabilities. This outside scooter lift works with any Class II hitch-equipped vehicle with a hitch from 5 to 19 inches high, and can support a scooter with a maximum width of 28.5 inches and a maximum wheelbase of 42 inches measured from the hub (center) of the front tire to the hub of the rear tire. The deck automatically folds up, out of the way, when empty. OPTIONS: A Sw

Urban Chamy Stroller

---- PROTOTYPE --------- PURPOSE: Urban Chamy combines transporting children and a helpful station for the babies at home. The concept is a shell equipped with two kinds of cushioning for the different ages of the baby. This shell is a comfortable cradle, before, and then a seat that can adapt on three different supports in relation to the different needs of moving, a base for car, a stroller-bike and a high chair for home. While the baby is sitting in the shell, the parent can ride the bike.

Uvl Series Van Lift

The UVL (Under Vehicle Lift) Series Van Lift is a platform van lift designed for use by wheelchair users. The lift is mounted underneath the vehicle so it does not take up space in the interior of the van and remains out of sight until deployed. The lift is electric for the in/out cycle and the outboard roll stop. The up/down cycle is hydraulic. All functions are controlled by the standard hand-held control or the optional remote control. The lift can be installed at the side door of domestic fu

Van Conversions

Van Conversions are designed to make Ford, Chrysler, Dodge, and Honda van models accessible to people who use wheelchairs. All conversions include a 10-inch lowered floor; complete undercoating, rust-proofing, and deluxe upgrade automotive carpet; power slide-out or manual ramp systems; emergency manual release and non-skid ramp surface; automatic sliding door with manual operation and full retention of original door latches; fully carpeted removable front seat base; original equipment manufactu

Van Seat Extention

CUSTOM ADAPTATIONPURPOSE: To enable transfers from the second row seat on the door side of a van, which was too distant for easy transfer. A padded box seat was built to temporarily fill the gap while the passenger enters the van. The box seat is removed to close the door. TITLE: The Van Seat Extention. WEB SITE: Workshop Solutions at http://www.workshopsolutions.com. REF: The originator, Tom Jeary, can be contacted at tlj@golden.net.

Vangater Ii

The Vangater II is a wheelchair van lift designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This power lift has a tri-folding platform. When the lift is in the stowed position, over half the van's side door is available for ambulatory exit and entry. The lift is electrically powered for both the fold/unfold and up/down cycles. Lift operation is controlled using a hand-held control, on-lift controls, or an optional remote control. It also features

Veigel Pedal Extensions For Brake And Gas

Veigel Pedal Extensions for Brake and Gas are accelerator and brake extensions designed for use by individuals with short stature or lower extremity disabilities. These extensions are designed to reduce the distance to the pedals and can be installed and removed quickly without tools. DIMENSIONS: The standard distance reduction is 2 to 5 inches but can be up to 12 inches.

Veigel Push-Rock Left Hand Cpntrol

The Veigel Push – Rock Left Hand Control is a hand control designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This control operates the accelerator by moving the handle in a circular motion toward the rear and downward. This can be done even while the hand rests on the wheel. Braking is done conventionally by pushing the handle forward. The control is located underneath the steering wheel and is operated with the left hand. Every motion of the ha

Veloped Tour

Veloped Tour is a rollator walker designed for individuals with arthritis, balance, lower extremity, or walking disabilities. The Veloped Tour's scientifically designed climbing wheel greatly increases the ability to maneuver obstacles like curbs and gutters with a minimal amount of force. The patent pending technology displaces the load between two wheels, providing suspension when walking on uneven surfaces, minimizing the shakes and wobbles synonymous with the more standard rollator designs

Ventrac Freedom (Model 300)

The Ventrac Freedom, model 300, is an all terrain vehicle designed to enable individuals who use wheelchairs to independently perform a variety of outdoor tasks. This open three-wheeled vehicle features a driver's compartment that enables the user to remain in his or her wheelchair. CONTROLS: Height- and tilt-adjustable handlebar steering with a forward/reverse lever. FWD: Front wheel drive. DRIVER COMPARTMENT (WxL): 32 x 50 inches. The compartment is wheelchair accessible and height-adjustable.

Versashuttle

VersaShuttle is a public transport van designed for use by individuals with mobility disabilities or spinal cord injury. This raised top van is available with standard or extended length on a Dodge or Ford chassis. Engine options include gasoline, diesel, or CNG alternative fueled engines. Wheelchair lift options include the Ricon PSL-10 Elevator lift or, on extended vans only, the Ricon "K" (KlearVue) series platform lift. The PSL-10 Elevator Lift (see entries) has a manual fold-out ramp to acc

Vision

Vision is a van conversion designed for use by individuals with mobility disabilities or spinal cord injury. This rear-entry, lowered floor modification is available on Daimler-Chrysler, Ford, and General Motors minivans. Conversion options include fully automatic entry and seating for four ambulatory passengers plus one wheelchair user, as well as all standard factory options. WARRANTY: Three years or 36,000 miles.

Vmi Full Size Van Conversions

The VMI Full-size Van Conversion is a van conversion designed for use by individuals who use wheelchairs. Features include lowered floor with an additional driver position drop which enables the vehicle to be driven from wheelchair or allows wheelchair to be located in front passenger position, added head room in the driver's position, driver and front passenger recessed seat belt retractors for more room to maneuver adaptive equipment in and out of front driver and passenger positions, raised r

Vmi Minivan Conversion

The VMI Minivan Conversion is a lowered floor van conversion desdigned for use by individuals who use wheelchairs. This conversion offers a lowered floor with a powered in-floor ramp for open, unrestricted entry and exit, as well as greater interior maneuverability. Features include a power door with manual operation, complete undercoating and rustproofing, emergency ramp release, automotive-quality interior with fully carpeted seat bases, and a manual wheelchair tie-down system. OPTIONS: Remote

Walker Carrier

---- CUSTOMIZED ADAPTATION --------- PURPOSE: To create a custom adapted walker carrier frame for an individual with mobility disabilities due to lymphoedema. The individual could not transport her walker in the trunk or back seat of the family car, even when folded. While there were some commercially available carrier frames none fit the walker frame or could be used independently by the individual. A custom adapted carrier, which would fit into the car’s existing towbar socket, and meet the NS

Wheelchair And Occupant Belt / Track System.

The Wheelchair and Occupant Belt/Track System has successfully impact tested at 30 MPH/20G. This test simulated the performance criteria required in FMVSS ##208, 209 and 210. Two models of shoulder restraints available, wall mounted non-retractable, and retractable. Tracks are installed in the floor of the van, in front and behind the chair, to lock the front and rear of the wheelchair frame in place. Web stiffeners are installed in the lap belt portion of the restraint to assist in connecting t

Wheelchair Chest Restraint

The Wheelchair Chest Restraint is a seat belt intended for use by people with lower extremity or mobility disabilities, spinal cord injury and others who use a wheelchair. This adjustable Velcro belt mounts onto wheelchair to secure occupant of chair. A separate restraint is needed to hold wheelchair securely to vehicle. Manufacturer states that this restraint should not to be used instead of an automotive seat belt.

Wheelchair Lift Sensing Mat

The Wheelchair Lift Sensing Mat is a lift sensor mat that is used to detect the presence of a wheelchair or scooter on a bus- or van-mounted lift. When installed on a lift, the mat can be used to signal the van or bus operator that the lift is ready for operation and to detect an unknown or unexpected person or object on the lift and prevent prevent the operator from stowing the lift or moving the vehicle until the object is off of the lift platform. This mat has a durable molded design with par

Wheelchair Ready Vehicle

---- PROTOTYPE --------- PURPOSE: To create a prototype of a wheelchair ready vehicle for individuals with mobility disabilities. Wheelchair users who, when selecting a vehicle, have their choice of minivans, and sometimes tall wagons, that have been "up-fitted" with needed equipment added and unneeded seats taken away. A South Florida-based start-up company, VPG, plans to begin offering a vehicle designed, engineered and built to be wheelchair-ready the MV-1 this fall. The MV-1's motorized ram

Wheelchair Seat Belt Lock Cover

"DO IT YOURSELF" ENTRY --- PURPOSE: To prevent children and adults with cognitive disabilities who use wheelchairs from unlocking a wheelchair seat belt. To make this cover, lay the material on flat surface with back facing up. Using straight pins, pin the edges together lengthwise along the material. With a sewing machine or needle, stitch along the pinned edge line lengthwise. Turn material right side out and slip onto one end of wheelchair seat belt. Fasten the belt and slide material over

Wheelchair Seatbelt Holdown (Model 126)

The Wheelchair Seatbelt Holdown, model 126, is a restraint system designed to keep wheelchair occupants secure when in a vehicle. The extra-long seatbelt straps attach to the floor with angles or Wheelwells (see separate entry), wrap around the armrests and in front of the wheelchair user.

Wijit

The Wijit is a wheelchair lever drive and braking system designed for use by individuals with mobility disabilities. The system includes a lever that attaches to each drive wheel of most manual wheelchairs, enabling the user to propel the chair using a pumping motion. The levers can be switched to reverse mode to enable the user to reverse directions. To engage the braking system to reduce speed or stop, the levers are simply pushed forward toward the body.

Woolfe Scooter Lift

The Wolfe Scooter Lift is a scooter loader for vans designed for use by individuals who use wheelchairs. This lift can be installed in most full-sized mini-vans by General Motors or mini-vans by other manufacturers that have a hatch opening of 38 inches or greater. No vehicle modifications are required as this lift is designed to connect directly to the third-row seating floor mounts. A press of a button activates the lift and it automatically emerges from the back of the vehicle and lowers to t

 
Processing...


Driving Walking/Biking Public Transit  Get Directions