Head and Neck Supports

Results: 101

"t"tube-Plate Weldment (Models 1521, 1521-01, 1522, & 1522-01)

The "T" Tube-Plate Assembly Weldment is headrest accessory interface hardware designed for positioning an Occipital Angle Bar or an Occipital "T" Bar on a wheelchair. The "T" Tube-Plate Weldment attaches to the rear of the occipital bar and slides through the 90-degree Vertical Tube attached to the back of the wheelchair. DIMENSIONS: Available in 4- or 6-inch lengths. COLOR: Available in black and stainless steel.

10 Inch Slide Mounting Kit (Models 3624 & 3624-01)

The 10 Inch Slide Mounting Kit is is headrest accessory hardware designed to attach the headrest, the occipital ring, and their interface hardware to the back of a wheelchair. The Kit consists of a Slide Bracket; a 10-inch, 90-degree Tube Slide; and two 3-Point Knobs. The Mounting Plate attaches to the back of the wheelchair with four sets of ##10-32 Screws and ##10-32 Nuts. COLOR: Available in stainless steel or black.

6628 Side Opening Head Support

The 6628 Side Opening Head Support is designed for use by individuals who are unable to independently maintain proper head positioning. Available in three sizes, this support cradles the entire head and may be used mounted or unmounted to a seating system or wheelchair. Made of closed cell vinyl-coated foam, the support features reinforced front and back plates, a hinge on one side, and a quick release buckle on the other side for ease in use. SIZES: Unmounted extra small, unmounted small, unmou

6630 C-Collar And 6635 Extended C-Collar

The 6630 C-Collar is a neck support contoured for the lateral and posterior neck areas to help prevent neck hyperextension. The 6635 Extended C-Collar is the same as the C-Collar with a clavical support added. Both collar can be used in conjunction with most seating units, and used during classroom activities and feeding. DIMENSIONS: C-Collar is 8 x 3.5 x 2 inches; the Extended C-Collar is 8 x 10 x 2 inches. COLOR: Black or Casa Tan.

6650 Half Mask

The 6650 Half Mask is a headrest accessory designed to provide head support for forward thrusting individuals. The mask follows the contours of the forehead and cheeks to help hold the head comfortably within a headrest. A replaceable terrycloth pad lines the foam mask, and an aluminum inner core allows the headpiece to be formed to fit the face. For mounting purposes, one side of of the mask can be attached directly to headrest; the opposite side fastens with snap buckles. OPTIONS: 6650 Mount P

6800 Seating Accessory System

The 6800 Seating Accessory System is designed to provide head and trunk support to feeder seats. A pre-formed aluminum bar incorporates an attached head positioner with the Danmar chest support. The chest support's lap belt goes through existing strap holes and the bar fits around the seat and is secured with channel brackets (included). SIZES: Small, with lateral head support provided by foam pads, wedged and formed, to cradle the head; Medium and Large, both with full C Collar for side suppor

6809 High Back Hensinger Head Support

The 6809 High Back Hensinger Head Support is a head and neck support that consists of the 6810 Hensinger Head Support (see separate entry) with a 1.5 to 2 inch higher back for additional occipital support. The cushions are made of vinyl coated foam. The device comes unmounted or mounted. SIZES: Extra Small, Small, Medium, and Large. COLOR: Blue or black.

6810 Hensinger Head Support

The 6810 Hensinger Head Support is a wrap around collar designed to support the head by using base support areas at the occiput and jaw line. Manufacturer recommends this support be used in conjunction with chest support to help maintain mid-line head positioning. (Proper head positioning should result in improved breathing, swallowing, and simplified feeding; and may also be conducive to more social interaction and awareness during classroom activities.) The support fastens with a one-snap rele

6812 Modular Head Rest

The 6812 Modular Head Rest with Mount Plate is a head and neck support designed for use with the Hensinger Break-Away-Mount Plate (see separate entry). An adjustable vertical connector attaches the two devices together. Three vinyl coated foam discs cradle the head and may be adjusted for the use of head switches. COLOR: Black.

6814 Lateral Head Support With Mount Bar

The 6814 Lateral Head Support with Mount Bar is a headrest designed for use with feeder seats that can be positioned to support from the occipital area and higher. The support is made of foam padding that comes around the sides of the head to provide support. SIZES: Small, Medium, Large, and Extra Large. COLOR: Bright blue, black, orange, red or teal. These custom colors are available for an additional $26: Baby blue, forest green, silver/gray, maroon, pink, purple, royal blue, casa tan, white a

6815 Hensinger With Mount Bar

The 6815 Hensiger with Mount Bar consists of the 6810 Hensinger Head Support (see separate entry) mounted on an aluminum bar designed to be attached to TumbleForm feeder seats or Danmar Trunk Support (see separate entries). The device slides over the seat with back buckle fasteners. Channel brackets for securing the bar after the head support is positioned are included. SIZES: Small, Medium, Large or Extra Large. COLOR: Bright blue. These custom colors are available for an additional $26: light

6821 Size Reducer

The 6821 Size Reducer is a foam insert designed to accommodate persons between sizes of the Hensinger Head Support (see separate entry). The vinyl coated foam insert fits into the inner circumference and has velcro straps which wrap around the head support. There are two models: Narrow and Wide. The narrow model can be used over or under the covers. The wide model adds some additional occipital support as the top foam piece folds over the back of the Hensinger. SIZES: Narrow or Wide. DIMENSIONS

6830 Sweep Headrest

The 6830 Sweep Headrest is a wrap around headrest with an occipital convex foam cushion built in across the bottom of the center pad to cradle the head. The support has two small wings that form the sides, angled at 60 degrees off center back pad. The heavy duty back plate has pre-threaded 1/4-20 metal inserts for mounting and eight 1-inch bushings which can be used as spacers to adjust the distance of the headrest to the head. The product can be ordered with or without mounting hardware. An opt

7 Inch Slide Mounting Kit Models 3621 & 3621-01)

The 7-Inch Slide Mounting Kit is is headrest accessory hardware designed to attach the headrest, the occipital ring, and their interface hardware to the back of a wheelchair. The Kit consists of a Slide Bracket; a 7-inch, 90-degree Tube Slide; and two 3-Point Knobs. The Mounting Plate attaches to the back of the wheelchair with four sets of ##10-32 Screws and ##10-32 Nuts. COLOR: Available in stainless steel or black.

7901 Hensinger Covers

The 7901 Hensinger Covers are replacement covers for the 6810 Hensinger Head Support and the 6809 Hensinger Head Support with High Back (see separate entries). They are made of a cotton blend. SIZES: Extra small, small, medium or large. COLOR: Black or blue.

7902 Hensinger Strap

The 7902 Hensinger Strap is a replacement straps with either a snap buckle or an adjustable slide buckle designed for the 6810 Hensinger Head Support and the 6809 High Back Hensinger Head Support (see separate entries). The straps are attached to the back plate. An optional velcro closure is available. SIZES: Extra small, small, medium or large. COLOR: Black.

7903 Hensinger Quick Release Mount Plate

The 7903 Hensinger Quick Release Mount Plate is a headrest accessory for the Hensinger Head Supports (see separate entries). The plate has 2 straps that attach the unit to the back of a seating unit. The Hensinger Head Support attaches to the plate with velcro. The velcro release will allow the head to move forward with the body. For permanent mounting, 2 screws are used to insure that the front and back plate stay connected. DIMENSIONS: 12 x 4 inches. COLOR: Black.

7914 Half Mask Otto Bock Mount Plate

The 7914 Half Mask Otto Bock Mount Plate is a headrest accessory designed to mount the 6650 Half Mask (see separate entry) onto the Otto Bock headrest. The mask mounts with adhesive foam backing for breakaway release in the event of emergency impacts. COLOR: Black.

90-Degree Tube Plate Weldment (Models 1511, 1511-01, 1512, 1512-01, 1513, & 1513-01)

The 90-Degree Tube Plate Weldment is headrest accessory interface hardware designed for positioning the wheelchair headrest. The 90-Degree Tube Plate Weldment attaches to the recessed area of the Headrest and slides through the 90-degree Vertical Tube attached to the back of the wheelchair. OPTIONS: A custom made 90-Degree Tube Plate Weldment is available. DIMENSIONS: Available in 4-, 6-, or 10-inch lengths. COLORS: Both the original and the custom made options are available in black and stainl

Acuback Heat Roller For Back Pain Relief

The Acuback heat roller is designed to relieve tension with therapeutic warmth. IT is microwavable and offers back and neck support. Nubby or textured supports create acupuncture-like therapy to release tight muscles and the design recreates the natural curve of the lumbar spine. Realigns the upper back and neck. Place it under neck, lower back, legs, or hands. Warm in microwave for one minute for 75 minutes of deep, soothing heat. Carrying case included.

Adjustable Head Support

The Adjustable Head Support is a padded head positioner with support legs designed to enable the head to be supported in prone, supine, or seated positions. The angle of support can be adjusted by altering the support legs. It may be useful for diagnostic testing, therapeutic massage, and cranial compression. OPTIONS: Extension legs are available. DIMENSIONS: Extension legs are five inches long.

Axion Rotary Interface For Wheelchair Headrests

The Axion Rotary Interface™ for Wheelchair Headrests is a headrest accessory designed for use by individuals with severe physical or neurological disabilities or spinal cord injury. This device permits wheelchair headrests to rotate, and it attaches to most existing wheelchair headrests and hardware. This unit is quiet, free-running, and it does not require lubrication. The range of rotation can be limited or stopped.

Contoured Headrest Assembly

The Contoured Headrest Assembly is designed for individuals requiring medial/lateral, posterior and rotary support. The ABS plastic construction allows for customized molding with a heat gun. The mounting hardware (included) allows height and forward/backward adjustment with a slide bracket and knob. The headrestt is also available upholstered. SIZE: Large (model ASCH-LG) or small (model ASCH-SM).

Deep U Headrest (Model Duhr100)

The Deep U Headrest, model DUHR100, is a wheelchair headrest designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and other people who use wheelchairs who need to keep their heads positioned upright and centered. DIMENSIONS: 11 x 5 inches.

Double Tube Lift-Off Mounting Kit (Models 3613 & 3613-01)

The Double Tube Lift-off Mounting Kit is headrest accessory hardware designed to attach the headrest, the occipital ring, and their interface hardware to the back of a wheelchair. The Kit consists of a Double Tube Lift-Off Mounting Plate, two 90-degree Vertical Tubes, and four 2 Point Knobs. The Mounting Plate attaches to the back of the wheelchair with four sets of ##10-32 Screws and ##10-32 Nuts. COLOR: Available in stainless steel or black.

Double Tube Mounting Kit (Models 3603, 3603-01)

The Double Tube Mounting Kit is designed to attach the headrest, the occipital ring, and their Interface hardware to the back of a wheelchair. The Kit consists of a Double Tube Mounting Plate, two 90-degree Vertical Tubes, and four 2-Point Knobs. The Mounting Plate attaches to the back of the wheelchair with four sets of ##10-32 Screws and ##10-32 Nuts. COLOR: Available in stainless steel or black.

Dynamic Forehead Strap System (Model Dfs-1)

The Dynamic Forehead Strap System is a headrest accessory designed to support the head for individuals who have difficulty maintaining their head in an upright position. It is meant for use with the S.O.F.T. headrest system (see separate entry). The system consists of pulleys that allow the forehead band to move with the user, providing greater freedom of movement. The strap is designed to float about freely with the user. The straps are available in two different styles. The first features a te

Extension Headrest (Model 72)

The Extension Headrest, model 72, is designed for use with wheelchairs with push handles. The unit attaches to the wheelchair push handles with bracckets (included) to extend the back upholstery to form the headrest extension. DIMENSIONS: Adds 18 inches to the wheelchair back height.

Front Mount Height Adjustment Headrest Bracket And Pads

Three custom size pads mounted on angled Kydex bracket which slips over top of tall solid back. Mounting knob in solid back secures headrest. Pads are 1/2 inch thick medium density foam over 1/2 inch birch plywood. May be ordered as unit ($140), or bracket ($40) or pads may be ordered separately.

Gerimate Bolster

The Gerimate Bolster is a back support cushion designed to offer support and comfort for persons using Geri-chairs. WARRANTY: If merchandise is received in damaged condition, a claim must be reported within five days from date of receipt of shipment.

Halo Strap

Soft velcro strap with mounting hardware and D-ring closure. Mounts to headrest system by attaching to lateral headrest pads. Cloth lining available on request.

Hat Holder Head Support

---- DO IT YOURSELF ENTRY --------- PURPOSE: To provide a do-it-yourself solution for a young lady with head mobility issues to keep her head from falling forward while communicating and/or eating. A sturdy post was attached to the back of the young lady’s wheelchair. Various hats, headbands, etc. were modified by adding a string and hook. The string and hook are attached to the post on the back of the wheelchair keeping the young lady’s head upright. TITLE: The Hat Holder. WEBSITE: Workshop S

Head Pod

The Head Pod is a head and neck support system designed for children with inadequate head control with combined hypotonia of the neck and trunk. Straps fitted around the user's head are connected to a support over the user's head which is attached to the rear of the user's wheelchair. Users who benefit from the Headpod include children ages 2-12 years old who are unable to sustain the weight of their own head due to neck weakness, provided that there is no high extensor tone in the trunk or sign

Head Rest Supports (Models 430C1, 430C2, 430H1, 430H10, 430N1 Series)

The Head Rest Supports are headrests and neckrests made from molded, contoured foam, and reinforced with flexible steel. They are available in large headrest, small headrest, combination headrest and neckrest, large neckrest, small neckrest, and lateral control. They can be modified as needed by bending the steel insert to the desired shape.

Head Stabilizer

The Head Stabilizer is a headrest designed for use with the tall models of the IncrediBack Rigid and Moldable Reclining Back Systems (see separate entries). Available in a moldable and a rigid model, the height-adjustable Head Stabilizer provides head and neck support and have lateral head support. The moldable version enables the lateral supports to be molded to conform to the head and neck. A moldable insert provides support for those with neck tone. The rigid support offers the same design, b

Head Support

DO IT YOURSELF ENTRY --- PURPOSE: To enable an individual with neurological disabilities to hold his head erect. A mold of the user's back was made of forming plastic and lined with 3/8-inch foam. The support is held in place with two-inch Velcro strapping. An upright rod made of 3/8 x 2 inch Lexan plastic (for stiffness) was attached to the top of the back piece. A padded, flexible head band made of 1/16 x 1.25 inch Lexan was attached to the top of the upright rod. Also, as an alternative to th

Head Support

The Head Support is a head positioner designed to disperse pressure on the head for individuals who must remain in a lateral or supine position for extended periods. The concave support features a triangular cut-out in the center to float the ear when the user is in a lateral position or the back of the head when supine. This support is available in a choice of economy or standard density.

Head Support System (Models Plush-1 & Plush-2)

The Head Support System, models PLUSH-1 and PLUSH-2, is designed to provide comfort and support for individuals who have difficulty holding their head in an upright position. The base is a durable metal panel which is padded with two layers of foam that makes them feel as soft as pillows. They are covered in zippered Darlexx fabric and are easy to remove for washing. This head support system comes with a choice of hardware: swingaway mounting hardware; detachable hardware; fixed mounting hardwar

Head-Mount For Chin Switch

--- "DO IT YOURSELF" ENTRY ------- A thermoplastic “hat” with an attached wire which is bent down around the face and under the chin. The switch is attached with Velcro to a small thermoplastic square at the end of the wire under the chin. PURPOSE: To stabilize a switch for activation using jaw movements. MATERIALS USED: Low temperature thermoplastic material, 18 inch x 6 inch sheet, preferably colored, stiff wire, such as hanger wire, about 20 inch long, plastic welder glue, pressure-sensitive

Headrest / Neckrest Hardware: Hardback Headrest Hardware (Models 430F7, 430F2, 430F6, & 430F5) & Sling Back Hardware (Model 446K1)

The Headrest and Neckrest Hardware, consisting of Hardback Headrest Hardware and the Sling Back Hardware, is a support system designed to attach Otto Bock headrests and neckrests to the back of a wheelchair. Model 430F7 has two ball joints for multi directional adjustability, including horizontal and vertical planes, for hard or rigid seat backs. Model 446K1 has attachment hardware for wheelchair frame of sling backs.

Headrest Pads

The Headrest Pads are headrest accessories designed for use on wheelchairs. These pads are composed of a steel insert with self-skinning polyurethane. These pads are designed to attach to a one-inch ball. SIZES: Small, medium, oe large.

Headrest, Large & Small (Models 1450, 1451-01, -21, -31, -32, -33, 1460, 1461-01, -21, -31, -32, -33)

The Headrests are designed for use with wheelchairs. Made of 16- gauge steel, they are plated to resist corrosion and have a recess in the center for two rows of ##10-32 press nuts. Both ends are contoured. The headrests are deburred for a smooth surface. OPTIONS: Available in metal only or with padding of 1 inch open cell foam, 3/8 inch closed-cell foam, and a cover. Covers are available in Terry, Lycra, and Heavy Weight Nylon. COLORS: Black, blue and red.

Headrest, Pad & Bracket

Headrest ($58.65 to 53.35). Easily removed pad has curved plastic base in 3 sizes. 1/2 inch foam cushioning, vinyl covered. Mounts to solid back insert with bracket ($108.35) which allows height, lateral and angle adjustments. 2 to 4 inches high, 5 to 9 inches wide.

Headsup Flexible Head Support System

HeadsUp is a head support designed for use by children and adults with neurological or severe physical disabilities or spinal cord injury. This support consists of a hat and flexible elastic bands that fasten around a wheelchair headrest or high seat or chair back to hold the head up. Each side adjusts independently from the other, creating the ability to apply the desired amount of tension. As the elastic stretches, it allows a full range of motion;as the elastic stretches, the resistance incre

Headwing Headrest

Two custom size pads, mounted to each side of tall solid back or splitback with angled Kydex brackets for lateral head support. Brackets slotted for adjustment of width. Pads are 1/2 inch thick medium density foam over 1/2 inch birch plywood. May be ordered as unit, or bracket or pads may be ordered separately.

Height Adjustable (Splitback) Headrest

Custom size pad and slotted aluminum bar mounts to shoulder height solid back with knob for easy removal and height adjustment. Pad is 1/2 inch thick medium density foam over 1/2 inch birch plywood. .

Hydro Support Configuration (Model Hsc-1)

The Hydro Support Configuration, model HSC-1, is head support system designed for supporting the enlarged heads of individuals with hydrocephalus. It is a collection of four modular pads allowing a wide variety of positioning and options. Each cushion is padded with high quality foam and locks securely into place with ball and socket brackets. The cover is sewn from Darlexx water resistant lycra that is soft to the touch against the head. This head support system comes with a choice of hardware:

Inflatable Neck Rest

The Inflatable Neck Rest is a neck support designed for use by individuals with arthritis. It supports the head whether sitting or lying down. It comes with a carrying pouch for storage when traveling. DIMENSIONS (HxDxW): 4 x 9.5 x 14 inches.

Interface Hardware

The Interface Hardware is headrest accessory hardware for the Occipital "T" Bar designed for positioning an occipital bar on a wheelchair. The Interface attaches to the rear of the occipital bar. DIMENSIONS: The swivel tubes are available in 4-, 6-, or 10-inch lengths. The "T" tubes are available in 4- or 6 inch lengths. COLOR: Available in black and stainless steel.

Large Oxbow Headrest (Model Lox100)

The Large Oxbow Headrest, model LOX100, is a headrest designed for use by use by individuals with lower extremity or mobility disabilities or spinal cord injury and other people who use wheelchairs who rotate their heads while seated in a wheelchair. It has flared ends that provide a flat area to rest the cheek when the head is turned to either side, and it is made of multi-layered foam with a zippered cover. DIMENSIONS (LxH): 16 x 8 inches.

Large Padded Headrest (Model Cph100)

The Large Padded Headrest, movel CPH100, s a wheelchair headrest designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and other people who use wheelchairs. This large multi-layered foam padded headrest provides comfort, support, and positioning. The headrest comes with a zippered Triptex cover. DIMENSIONS: 13 x 10 inches.

Lateral Facial Component (Model Lfc-1)

The Lateral Facial Component model LFC-1 is an accessory for the SOFT-1 or SOFT-2 headrest systems (see separate entries) that provides additional support to persons with severe ATNR or difficulty aligning in midline position. The support consists of two independently adjustable pads placed in front of the user's ears and extending from approximately the cheekbone to the crest of the head. The user's hearing or visual field is only minimally interfered by the device. The LFC-1 may be ordered thr

Ne-At Headrest Bracket

The NE-AT Headrest Bracket is headrest mounting hardware designed for people with neurological or mobility disabilities, spinal cord injury, cerebral palsy and other individuals who need adjustable head support. This hinged bracket has 0.25-inch countersunk mounting holes spaced 1 inch apart, with a spring loaded crank handle for tightening in tight spaces.

Ne-At Seat

The NE-AT Seat is a modular seating system of comfortable and supportive positioning pads designed for use in wheelchairs. Although each piece is available and can be used independently, the full NE-AT Seat comprises the NE-AT Seat, NE-AT Back, and NE-AT Headrest and is designed to fit into any mobility aid. The reusable and reshapable positioning pads are constructed of thick rubber bonded to nylon and filled with Styrofoam beads. This not only creates an airtight bladder, but adds cushionin

Neck Rest

The Neck Rest is a neck support designed to provide relief of pressure on the neck or shoulder muscles. The polyurethane foam support features a U-shaped groove in the center to support the neck. A polycotton cover is included. DIMENSIONS (WxHxL): 6 x 6 x 14 inches long. COLOR: The cover is available in white or blue.

Neck/shoulder Positioning Collar Assembly

The Neck/Shoulder Positioning Collar Assembly is a headrest designed to replace both occipital support and rigid shoulder positioners or other anterior thoracic supports for users with moderate to low "tone." The malleable aluminum collar provides posterior neck support and superior and anterior shoulder support. It is padded with closed cell foam and upholstered with nylon terry cloth backed with neoprene rubber. The mounting hardware (included) allows height and forward/back adjustment with a

Nodstop Special Needs

The Nodstop Special Needs is a head support designed for use by individuals with cerebral palsy, weak neck and shoulder muscles, or neurological disabilities such as amyotrophic lateral sclerosis (ALS) or multiple sclerosis (MS) who require assistance in holding their head upright while in a seated or semi-reclined position. It keeps the user's head, neck and shoulders in an upright position, and assists caregivers by holding up the user's head so the caregiver can have both hands free to feed t

Nodstop Travel

The Nodstop Travel is a head support designed for use as a comfort aid that promotes relaxation through support and stabilization of the head,neck and shoulders during travel, and by encouraging proper body mechanics and posture for healthy breathing and circulation. It can help provide restful sleep, relaxed neck and shoulder muscles, reduced pain and strain during travel, stabilized body posture and spine position, and improved breathing and circulation. It is for passengers using all modes o

Occi Dish

The OCCI Dish is a head support designed to relieve preesure from the back of the head. This support features a detachable cervical pad and a Durafilm-coated core for moisturer resistance.

Occipital "t" Bar (Model 1670)

The Occipital "T" Bar, model 1670, is a neck support designed for head, neck, trunk, and shoulder support for individuals with spinal cord injury or severe physical disabilities during wheelchair use. The bar is made of high strength aluminum alloy, padded with high resiliance foam tubing, and covered with a Lycra slip cover. The unit includes two quarter-inch-20 x 0.5 inch SHHD screws for attaching to the "T" Tube-Plate weldment. DIMENSIONS: The foam 1.5 inches in diameter. The bar is 6 3/8 inc

Occipital Angle Bar (Models 1681 & 1683)

The Occipital Angle Bar is a neck support designed to provide head, neck, trunk, and shoulder support for individuals with severe physical disabilities or spinal cord injury during wheelchair use. The bar is made of high strength aluminum alloy padded with high resiliant foam tubing and covered with a Lycra slip cover. The bars are U shaped with a 30-degree angle at the bends. The unit includes two quarter-inch 20 x 0.5 inch SHHD screws for attaching to the Swivel Tube or "T" Tube-Plate weldment

Occipital Bar Assembly

The Occipital Bar Assembly is a headrest designed to provide posterior head support for individuals with good medial/lateral and rotary head control. The straight (model ASOB-ST) and contoured (models ASOB-LC and ASOB-SC) occipital bars are padded with neoprene rubber and upholstered with nylon terry cloth backed with neoprene rubber. The mounting hardware (included) allows height and forward/backward adjustment with slide bracket and knob. DIMENSIONS: The Straight bar is 6 inches long. The Con

Occipital Headrest Systems & 2-Step Headrest Systems

The Occipital Headrest Systems are head supports designed to provide support beneath the occipital portion of the head, as well as laterally. An aluminum ban inside the headrest covers may be bent, shaped, or cut down. Models are available fixed and swing-away, with or without headbands (nos. 91100 to 93200). The 2-Step Headrest models are appropriate where additional surface area and contact are required. They have an ABS plastic base which can be heated and re-shaped for a more precise fit. Th

Occipital Ring With Hinge Bracket (Models 1456, 1455, 1467, & 1468)

The Occipital Rings are neck supports designed for head, neck, trunk, and shoulder support during wheelchair use. The ring is made of high-strength aluminum alloy and covered with high density tubular foam and a Lycra form-fitting slip cover. The hinge bracket at the back of the ring is designed to interface with the swivel tube hardware for use on a wheelchair. SIZES: Available in small child, large child, small adult and large adult. DIMENSIONS: The width between the support tubes is 3.5 inche

Offset Multi-Axis Headrest Hardware

The Offset Multi-Access Headrest Hardware is a headrest accessory designed for use by individuals with severe physical disabilities and spinal cord injury. This hardware comes with a horizontal bar and ring for attaching a headrest pad. Our headrest hardware also comes with a back clamp which attaches the vertical tube to the back of the chair. COLOR: Black chrome.

Orthocare Suprone Headrest (Model 2018)

The Orthocare Suprone Headrest ##2018 is a contoured headrest designed to provide stable supine or prone positioning. It is made of polyurethane foam, and has a cross ventilation slot for breathing. SIZES: One size fits all.

Otto Bock Tall Back And Modular Back Headrest Mounting Kit & Otto Bock Headrest Adapter Kit

The Otto Bock Tall Back and Modular Back Headrest Mounting Kit ($5) and the Otto Bock Headrest Adapter Kit ($20) are headrest accessories that allow attachment of Otto Bock headrest mounting hardware directly to the Jay Back cushion, compensating for the contour of the cushion.

Oval Head Support System (Model Ohs-1 & Ohs-2)

The Oval Head Support System, model OHS-1 and OHS-2, are head supports designed for individuals wo have difficulty holding their head up on their own. Both Designs are padded with high quality foam and lock securely into place with ball and socket adjustment. Model OHS-1 is designed for minimal support, while model OHS-2 is larger and designed for wide support and well padded for those with behavioral difficulties. Both pads are covered in Darlexx water resistant lycra that is soft to the touch

Oxbow Headrest (Model Ox100)

The Oxbow Headrest, model OX100, is a wheelchair headrest designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and other people who use wheelchairs who rotate their heads while seated in a wheelchair. It has flared ends that provide a flat area to rest the cheek when the head is turned to either side. DIMENSIONS: 15 x 4 inches.

Portable Workstation Table + Fan

This Portable workstation is designed for adults who carry their work with them. It can fold up to fit inside most laptop carrying bags. It is ergonomic and functional. Meant to unfold to an ideal height and prevent against neck/back aches. Has a built in fan which keeps the workstation cool. Its features include dual cooling fans, adjustable legs, an angled resting spot, a cup holder, a Universal Serial Bus (USB) extension cord. Built of heavy duty plastic. Includes instruction manual. Pen/penc

Power Headrest

The Power Headrest is a powered headrest and driving control system designed for use by individuals with upper extremity disabilities, severe physical disabilities, or spinal cord injury. This headrest features motorized activation to swing it into position for driving and to the storage position for unencumbered exit and entry into driving position. Its driving control function enables drivers with disabilities that limit hand/finger usage while driving to access turn signals, horn, dimmer, wip

Retractable Headrest System (Models 06-1 & 06-1S)

Retractable headrest system for high quad power recliners. Headrest moves to natural position for support and retracts compactly behind back when not in use. Replaces spreader bar for back stability. Has infinite height adjustment on back. Power recliner and head rest can be activated with common switch with available interface. 24 volt DC gear motor with overload protection. Available for all makes and models of reclining wheelchairs. Model 06-1 is for standard back; Model 06-1S is for sliding

Rolyan Cervical Roll (Model A818301)

The Rolyan Cervical roll, model A818301, is a neck pillow designed to assist with cervical spine alignment for persons with cervical pain and stress. This foam roll is wrapped with a cotton cover and helps to encourage proper neck flexion. It can be machine washed and dried. DIMENSIONS: (Length x Width) 18 x 4.25 inches.

S.o.f.t. Headrest System (Models Soft-1, Soft-2, Soft-3, Soft-4, & Soft-5)

The S.O.F.T. (Sub Occipital Formed Three-piece) Headrest System is a head and neck support designed to provide lateral cervical support. The device consists of a rear occipital pad and two sub occipital pads curved to allow ear clearance and to prevent "hooking". Each of the 3 components is independently adjustable. The support system also features ball and socket adjustments to provide an additional plane of movement. The total unit is attached to a height adjustable rod that is attached to the

Shane’s Neck Brace

Shane’s Neck Support Brace is designed to keep a user's head in an upright position without degrading the muscle tone from restricted movement. Made of flexible synthetic tubing, Shane’s Neck Brace: allows the head full range of motion with 360 degree support as needed; can be used for many neck conditions or injuries, and can help improve one’s posture and aid with balance and neck fatigue; is completely waterproof; comes in three adjustable sizes; is endorsed for several conditions by doctors,

Single Tube Lift-Off Mounting Kit (Models 3611 & 3611-01)

The Single Tube Lift-off Mounting Kit is designed to attach the headrest, or the occipital ring and its Interface hardware to the back of a wheelchair. The Kit consists of a Single Tube Lift-Off Mounting Plate, a 90-degree Vertical Tube, and two 2-Point Knobs. The Mounting Plate attaches to the back of the wheelchair with four sets of ##10-32 Screws and ##10-32 Nuts. COLOR: Available in stainless steel or black.

Single Tube Mounting Kit (Models 3601, 3601-01)

The Single Tube Mounting Kit is headrest accessory hardware designed to attach a headrest or the occipital ring and its Interface hardware to the back of a wheelchair. The Kit consists of a Single Tube Mounting Plate, a 90-degree Vertical Tube, and two 2-Point Knobs. The Mounting Plate attaches to the back of the wheelchair with four sets of ##10-32 Screws and ##10-32 Nuts. COLOR: Available in stainless steel or black.

Single Tube With Cross Tube Lift-Off Mounting Kit (Models 3612 & 3612-01)

The Single Tube with Cross Tube Lift-off Mounting Kit is headrest accessory hardware designed to attach the headrest, the occipital ring, and their interface hardware to the back of a wheelchair. The Kit consists of a Single Tube Lift-Off Mounting Plate, a 90-degree Vertical Tube, a 90-degree Cross Tube, and four 2-Point Knobs. The Mounting Plate attaches to the back of the wheelchair with four sets of ##10-32 Screws and ##10-32 Nuts. COLOR: Available in stainless steel or black.

Single Tube With Cross Tube Mounting Kit (Models 3602, 3602-01)

The Single Tube With Cross Tube Mounting Kit is headrest accessory hardware designed to attach the headrest, the occipital ring, and their Interface hardware to the back of a wheelchair. The Kit consists of a Single Tube Mounting Plate, a 90-degree Vertical Tube, a 90-degree Cross Tube, and four 2-Point Knobs. The Mounting Plate attaches to the back of the wheelchair with four sets of ##10-32 Screws and ##10-32 Nuts. COLOR: Available in stainless steel or black.

Sleepy Time Headrest

The Sleepy Time Headrest is a head and neck support designed for use by for children with neurological or physical disabilities sitting in car seats. Covered with cotton fabric, this support has a polyester fill that cradles the child's head and neck in all directions, without confining head movement. The Sleepy Time Headrest can be used in car seats, booster seats with backs, infant carriers, strollers, infant swings, wheelchairs, and feeder chairs. SIZES: Infant (for children up to 25 pound

Sliding Headrest Bracket

The Sliding Headrest Bracket is headrest mounting hardware designed for people with neurological or mobility disabilities, spinal cord injury or cerebral palsy. It is added to a headrest on a seat or wheelchair to enable headrest adjustments. This slotted interface bracket allows the headrest to be offset to either side, with infinite lateral adjustment up to 2 inches for an Otto Bock or NE-AT Headrest Bracket (see separate entry). This bracket attaches to the seating system using the existing h

Slip-On Portable Cafeteria Bench

The Slip-On Portable Cafeteria Bench promotes social interaction, independent sitting, and self-feeding. The seat can be used at any table in a cafeteria which aids in choice-making and builds self-esteem. *Adaptive Design products are custom-ordered; dimensions and weight capacity will vary with each order.

So Soft Deep U Headrest (Model Ssdu100)

The So Soft Deep U Headrest, model SSDU100, is a wheelchair headrest and head support designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and other people who use wheelchairs and need to keep their heads positioned upright and centered. This unit has aggressive laterals for maintaining head position, tapered for minimal interference of vision. The headrest has a firm foam base topped with a 1-inch layer of visco/memory foam to provide pressure reli

So Soft Oval Headrest (Models Sso100S & Sso200L)

The So Soft Oval Headrest, models SSO100S and SSO200L, is a wheelchair headrest designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and other people who use wheelchairs. The headrest has a contoured shape for lateral support. It has a firm foam base topped with a 1-inch layer of visco/memory foam to provide pressure relief and comfort. The headrest comes with a zippered Triptex cover. SIZES: Small (SSO100S) or large (SSO200L). DIMENSIONS: 11 x 5 in

So Soft Quad Headrest (Model Ssq4100)

The So Soft Quad Headrest, model SSQ4100, is a wheelchair headrest and head support designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and other people who use wheelchairs. The unit is slightly contoured for comfort and positioning. It has a firm foam base topped with a 1-inch layer of visco/memory foam to provide pressure relief and comfort. This headrest comes with a zippered Triptex cover. DIMENSIONS: 9 x 6.5 inches.

Standard Curved Padded Headrest (Model Hrc100)

The Standard Curved Padded Headrest, model HRC100, is a wheelchair headrest designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury and other people who use wheelchairs. It has a contoured U shape for positioning, and foam padding with a zippered Triptex cover. DIMENSIONS: 11 x 4 inches. Padding is 2.5 inches deep.

Stealth Comfort Plus Headrest (Models Asl909 & Asl910)

The Stealth Comfort Plus Headrest, models ASL909 & ASL910 are wheelchair headrests designed for use by individuals with mobility disabilities. The large padded headrests come with fixed mounting hardware. Padded with dual layers of premium foam, these headrests come with a plush slip-on Darlexx cover. They have metal backs and come with half-inch square Otto-Bock style headrest hardware. OPTIONS: Flip-down headrest hardware (model ASL617); adjustable/removable headrest hardware (model ASL623

Stealth Elite Headrest (Model Sm-Se210)

The Stealth Elite Headrest, model SM-SE210, is a headrest designed for use by individuals who use wheelchairs. This headrest is intended for individuals who do not need a midline cue. The two lateral swing-away components can be used for switch mounting and if a sensor is added in the backpad, it can also be equipped for computer access.

Stealth Ultra Headrest (Model Sm-Su200)

The Stealth Ultra Headrest, model SM-SU200, is a combination wheelchair headrest and switch mounting hardware designed for use by individuals with severe physical or neurological disabilities or spinal cord injury. The sub occipital component aids the user in finding the midline. The two lateral swing-away components can be used for sensor mounting and a sensor can also be mounted in the backpad.

Support For Drooping Head.

--- "DO IT YOURSELF" ENTRY ------- PURPOSE: A pulley device to assist holding head erect for persons with degenerative disease of the central nervous system. A three foot wooden ski tip has a slot cut in the tip and a stationary pulley is mounted on the back of the ski. The ski is installed vertically in the middle of the back of the wheelchair by use of U-shaped metal clamps which fasten the ski to the back upholstery of the chair. a smaller pulley is attached at midline about 6 inches below th

Swivel Tube (Models 3715, 3715-01. 3716, 3716-01, 3717, & 3717-01)

The Swivel Tube is neck support interface hardware designed for positioning an occipital ring on a wheelchair. The Swing Tube attaches to the hinge bracket on the occipital ring and slides through the tube mount attached to the wheelchair back. DIMENSIONS: The Swivel Tubes are available in 4-, 6-, or 10-inch lengths. COLOR: Available in black and stainless steel.

Swivel Tube Assembly (Models 1501, 1501-01, 1502, 1502-01, 1503, & 1503-01)

The Swivel Tube Assembly is headrest accessory interface hardware designed for positioning an occipital angle bar on a wheelchair. The Swivel Tube Assembly attaches to the rear of the occipital bar and slides through the 90-degree Vertical Tube attached to the wheelchair back. DIMENSIONS: Available in 4-, 6-, or 10-inch lengths. COLOR: Available in black and stainless steel.

Swivel Tube Assembly (Parts 1501, 1501-01, 1502, 1502-01, 1503, 1503-01)

The Swivel Tube Assembly is interface hardware designed for positioning a wheelchair headrest. The Swivel Tube Assembly attaches to the recessed area of the headrest. OPTIONS: A custom made Swivel Tube Weldment is available. DIMENSIONS: Available in 4-, 6-, or 10-inch lengths. COLOR:Both the original and the custom made options are available in black and stainless steel.

Top Mount Multiple Adjustment Headrest Bracket And Pads

Three custom size pads mounted on angled Kydex or aluminum bracket which attaches to shoulder height solid back. Mounting knob in solid back secures headrest, allowing it to be removed. Hardware allows height, tilt, and forward and back adjustment. Pads are 1/2 inch thick medium density foam over 1/2 inch birch plywood. May be ordered as unit, or bracket or pads may be ordered separately. Components: $50.00 to 40.00 brackets, $134.00 headwing bracket and pads.

Travelin' Toddler's Car Cushion

The Travelin' Toddler's Car Cushion is a head support, polybag cushion designed to offer support and comfort while sleeping for children when traveling. WARRANTY: If merchandise is received in damaged condition, a claim must be reported within five days from date of receipt of shipment.

Tumble Forms Carrie Collar (Model 2774C)

The Tumble Forms Carrie Collar, model 2774C, is a head and neck support designed to support the jawline and occipital region to help improve head control, neck flexion, and midline positioning for children who have physical disabilities. The collar may be used alone or with other seating systems. The horseshoe-shaped collar slips over the head, extends to the chest, and fastens in the front with a quick-release hook-and-loop fastener. The collar features the Tumble Forms waterproof coating.

Unilateral Facial Component (Models Ufc-1,-2,-3 & -4)

The Unilateral Facial Component, models UFC-1, UFC-2, UFC-3 and UFC-4, is a support designed for holding one side of the face or head for individuals who have difficulty holding their head in a mid-line position. It is similar to the Lateral Facial Component but is recommende for providing additional support to the individual with mild ANTR. The single adjustable pad can be positioned for greatest support and then locked securely into place using ball and socket brackets. It comes in four differ

Universal Headrest Mounting Plate (Model 7730)

The Universal Headrest Mounting Plate is seating hardware designed for use with wheelchair headrests. This plate enables a variety of headrests from various manufacturers to be interchanged as needed. The headrests may be changed without having to redo the T-nuts in the back.

Vertically Adjustable Solid Back Mount Head/neck Support (Model 107-1000) & Multi Adjust Head/neck Support (Model 107-2000)

Head and neck support component for adaptive positioning. 4 3/4 inch range of vertical adjustment, or Multi Adjust mounts with bracket to permit vertical, front to rear, tilt and rotational adjustment. 1/4 inch ABS plastic, with separate removable foam pad. Shape allows posterior support at the occiput and rotational control without ear irritation. Mounts on solid back. Sizes: small, medium, large and extra large. Options: custom sizes, hydrocephalus modification, off set mounting. Accessories:

Whit Kit (Model A0001)

The Whit Kit, model A0001, is a large selection of head supports allowing the clinician to evaluate what head support system works best for the client. It includes head support pads and hardware which let the clinician create custom solutions by mixing and matching components. They come packed in a hard shell plastic case for transporting. Also included is the Quik Mount hardware bracket (see separate entry) for fast and simple assembly and adjustment on any wheelchair. Whit Kit comes complete w

Zippie Head And Neck Telescoping Support System

Three-piece headrest with center pad and two adjustable side pads. Standard pad sizes: center 4 inches wide by 6 inches high, side pads 4 inches wide by 2 inches high. Custom sizes available. Center pad has occipital shelf or can be ordered flat. Mounting hardware allows adjustment of side pad depth, angle, and width, and adjustment of entire headrest in height, forward/back, and angle. Attaches to solid back.

 
Processing...


Driving Walking/Biking Public Transit  Get Directions