Headrest Accessory

Results: 30

"t"tube-Plate Weldment (Models 1521, 1521-01, 1522, & 1522-01)

The "T" Tube-Plate Assembly Weldment is headrest accessory interface hardware designed for positioning an Occipital Angle Bar or an Occipital "T" Bar on a wheelchair. The "T" Tube-Plate Weldment attaches to the rear of the occipital bar and slides through the 90-degree Vertical Tube attached to the back of the wheelchair. DIMENSIONS: Available in 4- or 6-inch lengths. COLOR: Available in black and stainless steel.

10 Inch Slide Mounting Kit (Models 3624 & 3624-01)

The 10 Inch Slide Mounting Kit is is headrest accessory hardware designed to attach the headrest, the occipital ring, and their interface hardware to the back of a wheelchair. The Kit consists of a Slide Bracket; a 10-inch, 90-degree Tube Slide; and two 3-Point Knobs. The Mounting Plate attaches to the back of the wheelchair with four sets of ##10-32 Screws and ##10-32 Nuts. COLOR: Available in stainless steel or black.

6650 Half Mask

The 6650 Half Mask is a headrest accessory designed to provide head support for forward thrusting individuals. The mask follows the contours of the forehead and cheeks to help hold the head comfortably within a headrest. A replaceable terrycloth pad lines the foam mask, and an aluminum inner core allows the headpiece to be formed to fit the face. For mounting purposes, one side of of the mask can be attached directly to headrest; the opposite side fastens with snap buckles. OPTIONS: 6650 Mount P

7 Inch Slide Mounting Kit Models 3621 & 3621-01)

The 7-Inch Slide Mounting Kit is is headrest accessory hardware designed to attach the headrest, the occipital ring, and their interface hardware to the back of a wheelchair. The Kit consists of a Slide Bracket; a 7-inch, 90-degree Tube Slide; and two 3-Point Knobs. The Mounting Plate attaches to the back of the wheelchair with four sets of ##10-32 Screws and ##10-32 Nuts. COLOR: Available in stainless steel or black.

7901 Hensinger Covers

The 7901 Hensinger Covers are replacement covers for the 6810 Hensinger Head Support and the 6809 Hensinger Head Support with High Back (see separate entries). They are made of a cotton blend. SIZES: Extra small, small, medium or large. COLOR: Black or blue.

7902 Hensinger Strap

The 7902 Hensinger Strap is a replacement straps with either a snap buckle or an adjustable slide buckle designed for the 6810 Hensinger Head Support and the 6809 High Back Hensinger Head Support (see separate entries). The straps are attached to the back plate. An optional velcro closure is available. SIZES: Extra small, small, medium or large. COLOR: Black.

7903 Hensinger Quick Release Mount Plate

The 7903 Hensinger Quick Release Mount Plate is a headrest accessory for the Hensinger Head Supports (see separate entries). The plate has 2 straps that attach the unit to the back of a seating unit. The Hensinger Head Support attaches to the plate with velcro. The velcro release will allow the head to move forward with the body. For permanent mounting, 2 screws are used to insure that the front and back plate stay connected. DIMENSIONS: 12 x 4 inches. COLOR: Black.

7914 Half Mask Otto Bock Mount Plate

The 7914 Half Mask Otto Bock Mount Plate is a headrest accessory designed to mount the 6650 Half Mask (see separate entry) onto the Otto Bock headrest. The mask mounts with adhesive foam backing for breakaway release in the event of emergency impacts. COLOR: Black.

90-Degree Tube Plate Weldment (Models 1511, 1511-01, 1512, 1512-01, 1513, & 1513-01)

The 90-Degree Tube Plate Weldment is headrest accessory interface hardware designed for positioning the wheelchair headrest. The 90-Degree Tube Plate Weldment attaches to the recessed area of the Headrest and slides through the 90-degree Vertical Tube attached to the back of the wheelchair. OPTIONS: A custom made 90-Degree Tube Plate Weldment is available. DIMENSIONS: Available in 4-, 6-, or 10-inch lengths. COLORS: Both the original and the custom made options are available in black and stainl

Axion Rotary Interface For Wheelchair Headrests

The Axion Rotary Interfaceâ„¢ for Wheelchair Headrests is a headrest accessory designed for use by individuals with severe physical or neurological disabilities or spinal cord injury. This device permits wheelchair headrests to rotate, and it attaches to most existing wheelchair headrests and hardware. This unit is quiet, free-running, and it does not require lubrication. The range of rotation can be limited or stopped.

Double Tube Lift-Off Mounting Kit (Models 3613 & 3613-01)

The Double Tube Lift-off Mounting Kit is headrest accessory hardware designed to attach the headrest, the occipital ring, and their interface hardware to the back of a wheelchair. The Kit consists of a Double Tube Lift-Off Mounting Plate, two 90-degree Vertical Tubes, and four 2 Point Knobs. The Mounting Plate attaches to the back of the wheelchair with four sets of ##10-32 Screws and ##10-32 Nuts. COLOR: Available in stainless steel or black.

Double Tube Mounting Kit (Models 3603, 3603-01)

The Double Tube Mounting Kit is designed to attach the headrest, the occipital ring, and their Interface hardware to the back of a wheelchair. The Kit consists of a Double Tube Mounting Plate, two 90-degree Vertical Tubes, and four 2-Point Knobs. The Mounting Plate attaches to the back of the wheelchair with four sets of ##10-32 Screws and ##10-32 Nuts. COLOR: Available in stainless steel or black.

Dynamic Forehead Strap System (Model Dfs-1)

The Dynamic Forehead Strap System is a headrest accessory designed to support the head for individuals who have difficulty maintaining their head in an upright position. It is meant for use with the S.O.F.T. headrest system (see separate entry). The system consists of pulleys that allow the forehead band to move with the user, providing greater freedom of movement. The strap is designed to float about freely with the user. The straps are available in two different styles. The first features a te

Halo Strap

Soft velcro strap with mounting hardware and D-ring closure. Mounts to headrest system by attaching to lateral headrest pads. Cloth lining available on request.

Headrest Pads

The Headrest Pads are headrest accessories designed for use on wheelchairs. These pads are composed of a steel insert with self-skinning polyurethane. These pads are designed to attach to a one-inch ball. SIZES: Small, medium, oe large.

Headrest Swing Away Bracket (Sm-Hrsa240)

The Headrest Swing Away Bracket, model SM-HRSA240, is switch mounting hardware designed for use by individuals who use wheelchair headrests. This arm attaches to any Stealth or Otto Bock style headrest (see entries). It is made ready to mount an egg switch or a sensor in a spot pad. Once adjusted in place the user can swing it away when it is not needed and push it back to the same spot when needed.

Headsup Flexible Head Support System

HeadsUp is a head support designed for use by children and adults with neurological or severe physical disabilities or spinal cord injury. This support consists of a hat and flexible elastic bands that fasten around a wheelchair headrest or high seat or chair back to hold the head up. Each side adjusts independently from the other, creating the ability to apply the desired amount of tension. As the elastic stretches, it allows a full range of motion;as the elastic stretches, the resistance incre

Interface Hardware

The Interface Hardware is headrest accessory hardware for the Occipital "T" Bar designed for positioning an occipital bar on a wheelchair. The Interface attaches to the rear of the occipital bar. DIMENSIONS: The swivel tubes are available in 4-, 6-, or 10-inch lengths. The "T" tubes are available in 4- or 6 inch lengths. COLOR: Available in black and stainless steel.

Lateral Facial Component (Model Lfc-1)

The Lateral Facial Component model LFC-1 is an accessory for the SOFT-1 or SOFT-2 headrest systems (see separate entries) that provides additional support to persons with severe ATNR or difficulty aligning in midline position. The support consists of two independently adjustable pads placed in front of the user's ears and extending from approximately the cheekbone to the crest of the head. The user's hearing or visual field is only minimally interfered by the device. The LFC-1 may be ordered thr

Ne-At Headrest Bracket

The NE-AT Headrest Bracket is headrest mounting hardware designed for people with neurological or mobility disabilities, spinal cord injury, cerebral palsy and other individuals who need adjustable head support. This hinged bracket has 0.25-inch countersunk mounting holes spaced 1 inch apart, with a spring loaded crank handle for tightening in tight spaces.

Offset Multi-Axis Headrest Hardware

The Offset Multi-Access Headrest Hardware is a headrest accessory designed for use by individuals with severe physical disabilities and spinal cord injury. This hardware comes with a horizontal bar and ring for attaching a headrest pad. Our headrest hardware also comes with a back clamp which attaches the vertical tube to the back of the chair. COLOR: Black chrome.

Otto Bock Tall Back And Modular Back Headrest Mounting Kit & Otto Bock Headrest Adapter Kit

The Otto Bock Tall Back and Modular Back Headrest Mounting Kit ($5) and the Otto Bock Headrest Adapter Kit ($20) are headrest accessories that allow attachment of Otto Bock headrest mounting hardware directly to the Jay Back cushion, compensating for the contour of the cushion.

Single Tube Lift-Off Mounting Kit (Models 3611 & 3611-01)

The Single Tube Lift-off Mounting Kit is designed to attach the headrest, or the occipital ring and its Interface hardware to the back of a wheelchair. The Kit consists of a Single Tube Lift-Off Mounting Plate, a 90-degree Vertical Tube, and two 2-Point Knobs. The Mounting Plate attaches to the back of the wheelchair with four sets of ##10-32 Screws and ##10-32 Nuts. COLOR: Available in stainless steel or black.

Single Tube Mounting Kit (Models 3601, 3601-01)

The Single Tube Mounting Kit is headrest accessory hardware designed to attach a headrest or the occipital ring and its Interface hardware to the back of a wheelchair. The Kit consists of a Single Tube Mounting Plate, a 90-degree Vertical Tube, and two 2-Point Knobs. The Mounting Plate attaches to the back of the wheelchair with four sets of ##10-32 Screws and ##10-32 Nuts. COLOR: Available in stainless steel or black.

Single Tube With Cross Tube Lift-Off Mounting Kit (Models 3612 & 3612-01)

The Single Tube with Cross Tube Lift-off Mounting Kit is headrest accessory hardware designed to attach the headrest, the occipital ring, and their interface hardware to the back of a wheelchair. The Kit consists of a Single Tube Lift-Off Mounting Plate, a 90-degree Vertical Tube, a 90-degree Cross Tube, and four 2-Point Knobs. The Mounting Plate attaches to the back of the wheelchair with four sets of ##10-32 Screws and ##10-32 Nuts. COLOR: Available in stainless steel or black.

Single Tube With Cross Tube Mounting Kit (Models 3602, 3602-01)

The Single Tube With Cross Tube Mounting Kit is headrest accessory hardware designed to attach the headrest, the occipital ring, and their Interface hardware to the back of a wheelchair. The Kit consists of a Single Tube Mounting Plate, a 90-degree Vertical Tube, a 90-degree Cross Tube, and four 2-Point Knobs. The Mounting Plate attaches to the back of the wheelchair with four sets of ##10-32 Screws and ##10-32 Nuts. COLOR: Available in stainless steel or black.

Sliding Headrest Bracket

The Sliding Headrest Bracket is headrest mounting hardware designed for people with neurological or mobility disabilities, spinal cord injury or cerebral palsy. It is added to a headrest on a seat or wheelchair to enable headrest adjustments. This slotted interface bracket allows the headrest to be offset to either side, with infinite lateral adjustment up to 2 inches for an Otto Bock or NE-AT Headrest Bracket (see separate entry). This bracket attaches to the seating system using the existing h

Swivel Tube Assembly (Models 1501, 1501-01, 1502, 1502-01, 1503, & 1503-01)

The Swivel Tube Assembly is headrest accessory interface hardware designed for positioning an occipital angle bar on a wheelchair. The Swivel Tube Assembly attaches to the rear of the occipital bar and slides through the 90-degree Vertical Tube attached to the wheelchair back. DIMENSIONS: Available in 4-, 6-, or 10-inch lengths. COLOR: Available in black and stainless steel.

Swivel Tube Assembly (Parts 1501, 1501-01, 1502, 1502-01, 1503, 1503-01)

The Swivel Tube Assembly is interface hardware designed for positioning a wheelchair headrest. The Swivel Tube Assembly attaches to the recessed area of the headrest. OPTIONS: A custom made Swivel Tube Weldment is available. DIMENSIONS: Available in 4-, 6-, or 10-inch lengths. COLOR:Both the original and the custom made options are available in black and stainless steel.

Universal Headrest Mounting Plate (Model 7730)

The Universal Headrest Mounting Plate is seating hardware designed for use with wheelchair headrests. This plate enables a variety of headrests from various manufacturers to be interchanged as needed. The headrests may be changed without having to redo the T-nuts in the back.

Parent Category: Head and Neck Supports
 
Processing...


Driving Walking/Biking Public Transit  Get Directions